SB450 Steel Plate: JIS G3103 Boiler and Pressure Vessel Plate

Sep 22, 2025 Leave a message

SB450 Steel Plate Overview

SB450 is a carbon steel plate for boilers and other pressure vessels specified in JIS G3103. It is a carbon-manganese grade with tightly controlled sulphur and phosphorus, intended for shells, drums, headers and formed parts of pressure equipment that operates under steady load at moderate wall thickness. Its moderate strength, good ductility and reliable welding behaviour make it a practical choice for general pressure and boiler fabrication.

SB450 is often selected alongside the higher-strength SB480 grade of the same specification, and the choice between them is made on design stress rather than on temperature class. Cutting and deep processing are offered for SB450 plate from 8 mm to 150 mm thick, delivered as profiled blanks, beveled rings, drilled tubesheets or machined parts with full heat number traceability.

Chemical Composition of SB450

Element Content, %
C 0.28-0.31
Si 0.15-0.40
Mn 0.90 max
P 0.030 max
S 0.030 max

The carbon range is the main strength carrier in this grade, with silicon used for deoxidation and a moderate manganese content for toughness and hot ductility. Sulphur and phosphorus are capped at 0.030% each, which limits the inclusion content that governs notch toughness and through-thickness ductility. SB450 is a carbon-manganese steel rather than a nickel-alloyed cryogenic grade: where low-temperature service above the standard impact requirement is needed, specifications that deliberately add nickel to the composition are used instead.

Mechanical Properties of SB450

Thickness Yield strength, min Tensile strength Elongation, min
25 mm and under 245 MPa 450-590 MPa 19%
Over 25 mm to 50 mm 245 MPa 450-590 MPa 23%

Yield strength is held at 245 MPa minimum across the rolled thickness range, with the tensile window fixed at 450-590 MPa so that the plate keeps a comfortable margin of ductility for rolling, flanging and dishing. The elongation requirement rises for heavier plate because the tensile test uses a longer gauge length. Charpy impact testing, where specified, is carried out on longitudinal specimens taken in the direction required by the purchase order.

Supply Condition, Toughness and Weldability

Plates are normally supplied in the as-rolled or normalized condition, and normalizing is applied when a uniform grain structure and stable impact values are required.

Additional heat treatment such as stress relief after forming is carried out when the fabrication sequence or the applicable code demands it.

The grade is welded with the common arc processes using matching carbon-manganese electrodes; low carbon and low sulphur keep the heat affected zone free of hardening cracks.

Thicker sections are given edge preparation and, where restraint is high, a modest preheat agreed in the welding procedure.

Because the carbon content is higher than in fine-grain normalized pressure steels, welding procedure qualification should confirm the impact and hardness requirements for the actual joint, particularly for plate above 40 mm where the cooling rate through the heat affected zone increases.

Cutting and Deep Processing of SB450 Plate

Flame cutting from 20 mm to 150 mm for contours, shells, nozzles and weld preparations, with preheat applied on heavy sections.

Plasma cutting from 8 mm to 50 mm for faster cutting with a narrow heat affected zone.

Waterjet cutting for cold cutting where the normalized condition must be preserved to the cut face.

Beveling, milling and drilling of edges, tubesheet holes and nozzle openings.

Rolling and forming of cylindrical shells and dished heads, followed by dimensional checking against the drawing.

Cut and formed parts are identified with the plate heat number, and mechanical properties assumed in the design are those reported on the mill certificate for that heat, not generic values for the grade.

Applications and Quality Control

Boiler shells, drums and headers

Pressure vessels and accumulators for general industry

Heat exchangers and condensers

Steam and water pressure piping components

Storage and process vessels in chemical and utility plants

Quality control covers ultrasonic examination of the plate before cutting where ordered, dimensional inspection of profiled parts, visual and penetrant examination of weld preparations, and verification that the delivered certificate matches the heat number on the part. Mill certificates report chemical analysis and the results of tensile testing for the thickness supplied.

Frequently Asked Questions

Q: What standard covers SB450 steel plate?
SB450 is specified in JIS G3103, the Japanese standard for carbon steel plates for boilers and other pressure vessels.

Q: What is the minimum yield strength of SB450?
The specified minimum yield strength is 245 MPa, with a tensile strength range of 450-590 MPa and minimum elongation of 19% for plate 25 mm and under, rising to 23% for heavier plate.

Q: Is SB450 a low-temperature steel?
It is a carbon-manganese boiler plate, not a nickel-bearing cryogenic grade. Its toughness is supported by low sulphur and phosphorus and by normalizing rather than by alloying additions.

Q: How does SB450 compare with SB480?
Both come from JIS G3103, but SB480 has a higher tensile requirement, so SB450 is used where design stress allows it and better ductility and welding tolerance are preferred.

Q: What thickness of SB450 can be cut and machined?
Cutting, beveling, drilling and forming are offered from 8 mm to 150 mm, with flame cutting used above 20 mm and preheat applied to heavy sections.

Q: Does SB450 need heat treatment after welding?
Post-weld heat treatment is not a property of the grade itself; it is decided by the applicable construction code and by the section thickness and restraint of the joint.