Types of Pressure Vessel Steel: Grades, Standards and Selection

Dec 27, 2023 Leave a message

What Makes a Steel Suitable for a Pressure Vessel

Pressure vessel steel is the plate, forging and tube material used for the main components of vessels and heat exchangers: shells, heads, transitions, nozzles and supports. The overwhelming majority of vessels are built from welded plate, and the plate is cold formed, hot formed and welded during manufacture. That process route sets the material requirements: good formability and weldability, enough strength to carry internal pressure and external loads, and sufficient toughness to rule out brittle fracture under normal working conditions. Because many vessels contain flammable or explosive media under pressure, toughness is treated as a safety property rather than a convenience.

The Main Families of Pressure Vessel Steel

Family Representative grades Typical specification Service notes
Carbon and carbon-manganese plate Q245R, Q345R (historic 20R, 16MnR), SA-516 Gr. 70 GB/T 713, ASTM A516 Ambient service, general shells and heads, the workhorse group
Low-alloy high-strength plate Q370R, 18MnMoNbR, 07MnMoVR, 07MnNiMoDR GB/T 713 Thicker walls, higher design pressure, reduced weight
Chromium-molybdenum heat-resistant plate 15CrMoR, 14Cr1MoR, 12Cr2Mo1R; SA-387 Gr. 11, Gr. 22 GB/T 713, ASTM A387 Elevated temperature, hydrogen and steam service
Low-temperature nickel steels 16MnDR, 15MnNiDR, 09MnNiDR, 08Ni3DR, 06Ni9DR; SA-203 Gr. E, SA-645, SA-553 Type I GB/T 3531, ASTM A203/A553 Design temperatures from about -40 °C down to -196 °C
Austenitic stainless and clad plate SA-240 Type 304, 304L, 316L, 321, 347 ASTM A240, clad/overlay plate Corrosive media, cryogenic service, lining of carbon steel shells

Carbon and Carbon-Manganese Steels

Carbon and carbon-manganese grades remain the most widely used vessel materials because they combine adequate strength with predictable welding and low cost. In the Chinese system the historic designations 20R and 16MnR have been superseded by Q245R and Q345R in GB/T 713, and older drawings that still call out 16MnR or 15MnVN should be re-mapped against the current standard before a purchase order is placed. Internationally, ASTM A516 Grade 70 is the equivalent workhorse: a normalised, fine-grained plate specified by minimum tensile strength rather than by yield, commonly used from about -29 °C up to 343 °C depending on thickness and design code.

Low-Alloy High-Strength and Chromium-Molybdenum Steels

Adding a small amount of manganese, molybdenum, vanadium or niobium raises strength without the thickness penalty that heavier carbon additions would bring. Q370R and 18MnMoNbR are typical of this group in GB/T 713, and the more recent 07MnMoVR and 07MnNiMoDR grades offer high strength with improved toughness for large diameter vessels. When the wall must also resist hydrogen attack and creep at high temperature, chromium-molybdenum plate is selected: 15CrMoR and 14Cr1MoR for moderate severity, and 12Cr2Mo1R or ASTM A387 Grade 22 for heavy-wall hydroprocessing reactors. In all of these grades carbon is held low, generally not more than about 0.20%, so that carbon equivalent and welding sensitivity remain manageable.

Low-Temperature Nickel Steels

Below about -20 °C the choice narrows to nickel-alloyed steels, where each nickel increment buys a lower ductile-to-brittle transition temperature. Typical steps are 0.5Ni, 1.5Ni, 3.5Ni, 5Ni and 9Ni, specified as 16MnDR and 09MnNiDR at the warm end of the cryogenic range and as 06Ni9DR or SA-553 Type I 9Ni steel for liquefied natural gas service at -196 °C. A 3.5Ni grade such as SA-203 Grade E serves at about -101 °C, and 5Ni steel extends to roughly -170 °C. Ni steel has progressively replaced austenitic stainless steel such as 1Cr18Ni9Ti in cryogenic tanks because the nickel grades deliver comparable toughness at lower cost, with the trade-off of more demanding welding procedures.

Selecting the Right Grade: A Practical Checklist

Fix the minimum design metal temperature first; it eliminates most of the family list immediately.

Check whether the governing code allows impact testing exemption for the proposed thickness.

Confirm the delivery condition, normalised, normalised-rolled, quenched and tempered, or thermomechanical.

Verify the carbon equivalent against the welding procedure and any preheat limits.

Confirm the corrosion allowance and whether a stainless clad or overlay plate is more economical than solid stainless.

Check availability in the required thickness and width before finalising the drawing.

Frequently Asked Questions

Q: What is the difference between Q345R and 16MnR?
They are the same class of carbon-manganese vessel steel; Q345R is the current GB/T 713 designation, while 16MnR is the older name still found on legacy drawings.

Q: Why is carbon content limited in pressure vessel steel?
Low carbon lowers carbon equivalent and welding sensitivity, which protects toughness in and around the weld heat-affected zone.

Q: When should nickel steel be used instead of stainless steel?
For cryogenic service where toughness, not corrosion resistance, is the deciding factor; 3.5Ni, 5Ni and 9Ni grades usually cost less than an austenitic equivalent.

Q: What does the R in a grade such as Q245R mean?
It denotes a plate grade intended for pressure vessels, distinguishing it from structural plate with a similar strength level.

Q: Can a vessel be built from more than one steel family?
Yes. Carbon-manganese shells with stainless clad or overlay internals, or nickel steel heads with stainless nozzles, are common arrangements.

Q: Which documents should accompany the plate?
A mill test certificate showing chemistry, tensile results and impact energy at the specified temperature, plus any heat treatment record.