SA203GrE Steel Plate 8-90 mm: Cutting and Deep Processing Services

Aug 22, 2025 Leave a message

SA203 Grade E and Its Place in the ASME System

SA203 Grade E is a nickel-alloy steel plate specification issued in ASME SA203/SA203M for pressure vessels in low temperature service. Grade E belongs to the 3.5 % nickel group of the specification, together with Grades D and F, and it is normally selected for welded pressure equipment in cryogenic processing, air separation and liquefied gas storage. The nickel addition is what delivers the combination of strength and notch toughness that plain carbon pressure vessel plate cannot provide at these temperatures.

Plates are ordered against the specification itself, supported by the general requirements of ASME SA-20/SA-20M, and the material is listed in ASME BPVC Section II Part A so that allowable stresses can be taken directly from the design tables of the construction code. That link between material specification and design code is the reason SA203 Grade E is written into the drawings of low temperature vessels rather than expressed as a generic nickel steel.

Chemical Composition of SA203 Grade E

Grade E is defined by its nickel content and by a tight control of carbon and impurities, which together protect toughness at the design temperature.

Element Content (%) Comment
C 0.20 max Carbon is capped so that toughness is not sacrificed
Si 0.13-0.45 Deoxidation range
Mn 0.70-0.80 Controlled narrow range for strength and toughness balance
P 0.035 max Impurity control
S 0.035 max Impurity control
Ni 3.25-3.75 Grade-defining element for low temperature toughness

Carbon equivalent is normally reported as Ceq = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15. The narrow manganese window is unusual for a pressure vessel steel and reflects the balance needed between strength and impact energy in the 3.5 % nickel matrix.

Mechanical Properties and Low Temperature Service Range

Property Requirement
Tensile strength Rm 485-620 MPa (70-90 ksi)
Minimum yield strength Re 275 MPa (40 ksi)
Minimum elongation in 50 mm (2 in) 21 %
Minimum elongation in 200 mm (8 in) 17 %
Normal impact test temperature -101 °C (-150 °F)

These values describe normalized plate. In the quenched and tempered condition the plate combines higher strength with a service range that reaches down to about -107 °C, which is why quenched and tempered material is preferred where the design metal temperature is at the lower end of the cryogenic window. Across the specification as a whole, Grade E is used for service from roughly -70 °C down to -101 °C, while Grade F with a still colder impact test temperature covers more demanding duties.

Plate Thickness, Sizes and Cutting Capability

Cryogenic equipment is built from a wide range of plate thicknesses, and cutting accuracy has a direct effect on fit-up quality and on the amount of edge preparation needed before welding.

Item Range
Thickness for cutting and deep processing service 8-90 mm
Thickness supply range 6-150 mm
Width 1500-4050 mm
Length 3000-15000 mm

Flame and plasma cutting for thick plate, with controlled kerf and post-cut edge cleaning.

Laser cutting for thin plate and for openings and nozzles where a narrow heat affected zone is important.

Waterjet cutting where a cold cut with no thermal influence on the low temperature microstructure is preferred.

Beveling and edge milling to prepare welding edges at the angle and root face required by the welding procedure.

Contour and CNC cutting of rings, discs, shells and bracket blanks from the marked and identified plate.

Every part keeps the heat number of the mother plate, so the material certificate remains valid through cutting and forming, and dimensional tolerances follow EN 10029 or the equivalent general requirements for rolled plate.

Deep Processing and Supplementary Requirements

Drilling, tapping and machining of flanges, support pads and nozzle areas.

Rolling of shells and segments for towers and storage vessels, with thickness and radius control.

Supplementary hydrogen induced cracking testing to NACE TM0284 where wet sour service is possible.

Sour service compliance to NACE MR0175/ISO 15156 when the vessel handles wet H2S containing streams.

Through thickness testing to the Z15, Z25 or Z35 quality classes of EN 10164 for weld restrained joints.

Ultrasonic testing to EN 10160 or ASTM A578, plus impact testing at additional temperatures when the design temperature is below the standard test point.

Post-weld heat treatment simulation, hardness surveys and dimensional reports to support fabrication qualification.

These supplementary requirements are not decorative: in cryogenic service the failure mode is brittle fracture, and each test above produces evidence that the plate and its welds still absorb energy at the design temperature.

Frequently Asked Questions

Q: What is SA203 Grade E steel plate?
It is a 3.5 % nickel-alloy pressure vessel steel plate specified by ASME SA203/SA203M for low temperature service, widely used in cryogenic processing and air separation equipment.

Q: What is the impact test temperature of Grade E?
The standard impact test is carried out at -101 °C, and quenched and tempered plate is applied at service temperatures down to about -107 °C.

Q: Which thickness range is available for cutting and processing?
Cutting and deep processing services cover 8-90 mm, within a supply range of 6-150 mm thickness, 1500-4050 mm width and 3000-15000 mm length.

Q: Which cutting method is best for cryogenic nickel plate?
Waterjet and laser cutting limit thermal input, while plasma and flame cutting are more economic for thick sections provided the cut edge is cleaned before welding.

Q: Where is SA203 Grade E typically used?
In low temperature separation units, air separation plants, liquefied gas storage equipment, absorption towers, concentration towers and methanol scrubbers in coal chemical plants.

Q: Which tests are required for sour or highly restrained service?
Hydrogen induced cracking testing to NACE TM0284, sour service compliance to NACE MR0175/ISO 15156 and through thickness testing to EN 10164 Z15, Z25 or Z35 can be added to the order.