Why Construction Machinery Uses the 690 MPa Class
Q690D is a low alloy high strength structural steel plate standardised in GB/T 1591-2018 with a minimum yield strength of 690 MPa and grade D impact testing at minus 20 degrees Celsius. In construction machinery the grade is selected for one commercial reason above all others: a higher allowable stress allows a thinner section for the same load, and a lighter structure increases payload, reduces fuel consumption and lowers the load on every supporting component in the machine.
The second reason is fatigue. Machines such as cranes, excavators and loaders accumulate millions of load cycles over their service life, and a higher strength plate used at a controlled stress level can be detailed so that fatigue sensitive connections experience lower stress ranges. This is why the grade is applied to primary load carrying members rather than to secondary panels.
Application Areas in Construction Machinery
| Equipment | Typical Q690D components | Reason for selection |
|---|---|---|
| Cranes and tower cranes | Boom sections, jib, mast, frame, outrigger beams | Weight reduction in long cantilever members |
| Excavators | Boom, arm, bucket linkage, undercarriage frames | High load capacity with reduced moving mass |
| Loaders | Lift arms, frame, bucket structure | Compact welded structure with high stiffness |
| Concrete machinery | Boom sections of pump trucks, support frames, mixer drum frames | Long reach with controlled dead weight |
| Earthmoving equipment | Blade and ripper structures, dozer frames, roller frames | Resistance to high alternating loads |
The plate also appears in mining shovels, drilling rig masts, aerial work platforms, forklift masts and port handling equipment, in each case where a compact section must transmit a heavy concentrated load.
Delivery Condition and Specification Practice
Q690D is supplied in a thermomechanically rolled or quenched and tempered condition, with the exact condition recorded on the certificate. Thickness coverage is normally from around 3 mm to 150 mm, and for a given order the designer states the required impact class, the carbon equivalent limit and any through thickness requirement. Where the structure is welded under high restraint, Z15, Z25 or Z35 through thickness quality is ordered together with ultrasonic testing.
Impact class: grade D gives 47 J minimum at minus 20 degrees Celsius, which suits most outdoor machinery.
Surface quality: plate is ordered with a defined surface condition because fatigue cracks often initiate at a surface discontinuity.
Tolerances: thickness and flatness tolerances are tightened for laser cut linkage components.
Documentation: full heat traceability, mechanical test results and dimensional records accompany each shipment.
Fabrication Practice for Machinery Builders
Machinery fabricators cut Q690D by plasma, laser or flame process, with preheat applied above about 20 to 25 mm thickness. Cold bending is performed with large radii and with tooling that is rigid enough to control springback, and cut edges are dressed where a fatigue sensitive detail is located. Machined bores and pin holes are produced after welding so that distortion is removed by machining rather than by flame straightening.
Welding is carried out to a qualified procedure with consumables matched to the 690 MPa class and with low hydrogen practice. Heat input is controlled, preheat is applied, and interpass temperature is limited. Where a weld terminates at a fatigue critical detail, the toe is usually dressed by grinding or a similar finishing operation to remove the geometric stress concentration.
Common Misconceptions and Quality Control
A frequent misconception is that the suffix D refers to the delivery condition. It does not: the letter records the impact test temperature, so Q690D is tested at minus 20 degrees Celsius while Q690E is tested at minus 40 degrees Celsius. Both can be supplied thermomechanically rolled or quenched and tempered. A second common error is to treat all 690 MPa plate as interchangeable between suppliers, when in practice the carbon equivalent, the impact direction and the through thickness properties can differ, and these differences affect both weldability and the fatigue life of a finished machine.
Quality control for machinery applications extends beyond the mill certificate. Fabricators typically verify incoming plate by hardness survey, ultrasonic examination for critical members, dimensional checking of cut parts against the drawing, and weld inspection. Reproducible results depend on stable plate supply, which is why long production programmes are usually placed against a fixed specification rather than a generic grade reference.
Frequently Asked Questions
Q: What impact temperature applies to Q690D?
A: Grade D is tested at minus 20 degrees Celsius with a minimum absorbed energy of 47 J, while grade E is tested at minus 40 degrees Celsius.
Q: Why use 690 MPa plate instead of 355 MPa plate?
A: The higher allowable stress allows thinner sections, so a machine can be lighter or carry more payload without a loss of load capacity.
Q: What thickness range is typical?
A: Plate is commonly supplied from around 3 mm up to 150 mm, with machinery applications concentrated between 6 mm and 60 mm.
Q: Is preheat needed for welding?
A: Preheat is applied according to thickness and carbon equivalent, and is standard practice for thicker sections in this strength class.
Q: Can the plate be bent cold?
A: Yes, but with larger bend radii and more springback than ordinary structural steel because of the high yield strength.
Q: Which through thickness options are available?
A: Z15, Z25 and Z35 quality can be supplied with ultrasonic testing for restrained welded connections.







