Reading the Grade Designation
16MnDR is a low temperature pressure vessel steel plate. The designation carries the essential information in a few characters: 16 indicates that the carbon content is about 0.16 percent, Mn identifies manganese as the principal alloying element, D marks the grade as suitable for low temperature service and R identifies it as steel for pressure vessels. The manganese figure is written in the same shorthand that appears in older Chinese steel names, where a nominal 1.5 to 1.6 percent manganese addition is expressed as 16Mn.
The service temperature behind the D in the grade is minus 40 degrees Celsius. That is the design condition the plate is bought for, and it drives everything else about the material: the chemistry window, the delivery condition, the impact test temperature and the inspection regime.
Chemistry Concept and Standard Basis
The steel is a carbon-manganese plate rather than an alloyed cryogenic grade. Strength comes from the manganese addition and from grain refinement, while toughness at low temperature is achieved by keeping carbon and residual elements low and by normalising the plate to produce a uniform ferrite-pearlite microstructure with a fine grain size. Because the grade does not rely on nickel or other expensive additions, it is an economical choice for the temperature band it covers, and it is one of the most widely used low temperature vessel steels in general engineering.
Low temperature pressure vessel plates are covered by the Chinese pressure vessel steel plate standards, with GB/T 713.2-2023 providing the framework for non-alloy and alloy plates with specified temperature properties, and dimensional and inspection requirements referenced to the general plate and ultrasonic testing standards. The material certificate reports heat analysis, tensile properties and Charpy V-notch impact energy at the specified test temperature.
Delivery Condition and Inspection Requirements
| Item | Requirement |
|---|---|
| Design service temperature | Minus 40 degrees Celsius |
| Delivery condition | Normalised |
| Ultrasonic testing, thickness above 20 mm | Sheet by sheet, performed by the supplier |
| Ultrasonic testing, thickness 20 mm and below | By agreement between purchaser and supplier |
| Mechanical testing | Tensile and low temperature Charpy V-notch impact testing in the delivery condition |
The ultrasonic testing rule is worth noting because it is written into the supply requirement rather than being an optional extra. Plate thicker than 20 mm is tested sheet by sheet so that internal discontinuities cannot escape detection, while for thinner plate the test can be applied by agreement. The acceptance class and the testing standard are stated in the purchase order, and the results are recorded with the plate identification.
Fabrication and Welding Notes
Forming: cold forming is practical within agreed limits; hot forming requires a normalising treatment afterwards to restore the specified properties.
Welding: low hydrogen consumables matched to the plate strength, with preheat and interpass temperature controlled according to thickness and joint restraint.
Heat input: kept within a moderate band so that the heat affected zone retains its low temperature toughness.
Post-weld heat treatment: applied where thickness or service conditions require it, with attention to the effect of the cycle on impact properties.
Quality control: ultrasonic testing, dimensional verification and full heat number traceability on the material certificate.
Applications
16MnDR plate is used for low temperature pressure vessels and storage equipment in petroleum, chemical, gas processing and power plants, including cryogenic storage tanks, heat exchangers, separators and transport vessels for liquefied gases. It is also used for structural and pressure components that must remain safe when the ambient temperature falls below the transition range of ordinary carbon steel.
Frequently Asked Questions
Q: What does 16MnDR mean?
A: 16 indicates a carbon content of about 0.16 percent, Mn stands for manganese, D indicates low temperature service and R indicates pressure vessel steel.
Q: What is the service temperature of the grade?
A: The plate is designed for pressure vessel service at minus 40 degrees Celsius.
Q: How is the plate delivered?
A: In the normalised condition, which gives the uniform microstructure needed for low temperature toughness.
Q: When is ultrasonic testing required?
A: Sheet by sheet ultrasonic testing is required for plate thicker than 20 mm; for thinner plate it can be applied by agreement.
Q: Which standards apply?
A: The low temperature pressure vessel plate requirements of the Chinese plate standards, with GB/T 713.2-2023 providing the framework for plates with specified temperature properties and GB/T 247 covering packaging, marking and certification.






