Grade Identity and Standard Reference
07MnMoVR is a tempered high strength steel plate for pressure vessels. The designation records a very low carbon content, manganese and molybdenum as the principal alloying elements, and the final R that identifies pressure vessel steel. The low carbon level, supported by a quenched and tempered treatment, is the core of the design idea: strength comes from the heat treatment and the alloy combination rather than from carbon, so the plate keeps good toughness and remains weldable in heavy sections.
Plates are produced to GB 19189, the standard for quenched and tempered high strength steel plates for pressure vessels. The current edition replaced the previous one and, in doing so, changed the former grade 07MnCrMoVR to 07MnMoVR, reflecting a chemistry adjustment towards molybdenum rather than chromium as the strengthening carbide former. Designers working from older drawings should note the grade change when they convert a specification to the present designation.
Scope, Thickness and Delivery Condition
| Item | Requirement |
|---|---|
| Standard | GB 19189 |
| Grade | 07MnMoVR, replacing 07MnCrMoVR in the earlier edition |
| Thickness range | 10 mm to 60 mm |
| Delivery condition | Quenched and tempered, with tempering temperature not less than 600 degrees Celsius |
| Cutting and supply | Delivered sheared or flame cut, with edges prepared as agreed |
The thickness ceiling of 60 mm is a defining feature of the specification. Within that range the quenched and tempered treatment develops uniform properties, and the plate can be supplied sheared or flame cut to the ordered size, which saves fabrication time for shops that cut and form shell plates themselves. Above 60 mm a different grade or a special agreement is normally required.
Metallurgy and Performance
The plate is made from electric furnace steelmaking with careful control of the charge and the melt, followed by vacuum treatment that lowers gas and residual element content. Clean steel is not a marketing phrase in this context: low sulphur and low gas content directly improve toughness, reduce the risk of lamellar tearing in thick welded joints and reduce the scatter in Charpy test results. The quenched and tempered structure that follows is a fine, uniform microstructure with a high yield to tensile ratio, which is what allows the designer to use a thinner wall than a conventional vessel steel would permit.
Tempering at not less than 600 degrees Celsius ensures the plate is properly softened after quenching and that the heat affected zone of welds made on site behaves predictably under subsequent thermal cycles.
Application Spectrum
07MnMoVR plate appears across a very wide band of process equipment: reactors, heat exchangers, separators, spherical tanks, oil and gas tanks, nuclear reactor pressure shells, boiler drums and steam drums, high pressure penstocks for hydroelectric stations and turbine spiral cases. The industries are petroleum, chemical, power station and boiler construction. The heaviest demand comes from petrochemical processing, coal conversion, nuclear power, turbine cylinder manufacture and thermal power, where equipment must survive complex and corrosive media. Reference equipment includes water washing towers, conversion furnaces, coke towers, desulphurisation tanks, gas waste heat boilers, methanation furnaces and heaters, regenerators, hydrogenation reactors and conversion gas steam generators.
Fabrication and Quality Control
Forming: cold forming within agreed limits, or hot forming followed by a heat treatment that restores the quenched and tempered condition.
Welding: low hydrogen consumables matched to the strength class, with preheat and interpass temperature controlled according to thickness and restraint.
Cutting: shearing or flame cutting, with cut edges ground or machined before welding.
Inspection: ultrasonic testing sheet by sheet and mechanical testing in the delivery condition.
Testing: tensile and impact tests as required by GB 19189, with simulated post-weld heat treatment on request.
Documentation: quality certificate with heat number traceability for every plate supplied.
Frequently Asked Questions
Q: What standard covers 07MnMoVR plate?
A: GB 19189, the standard for quenched and tempered high strength steel plates for pressure vessels.
Q: Which grade did 07MnMoVR replace?
A: It replaced the former grade 07MnCrMoVR when the standard was revised.
Q: What thickness range is covered?
A: The standard applies to plate from 10 mm to 60 mm thick.
Q: What is the delivery condition?
A: Quenched and tempered, with the tempering temperature not lower than 600 degrees Celsius.
Q: Why is a low carbon chemistry used?
A: Low carbon keeps toughness high and makes the plate weldable in heavy sections, while the quenched and tempered treatment and the manganese and molybdenum addition provide the strength.






