Grade Identity and Material Concept
12MnNiVR is a quenched and tempered high strength steel plate for pressure vessels and is best known as a plate for large oil storage tanks. The designation names its constituents directly: Mn is manganese, Ni is nickel, V is vanadium, and R marks the pressure vessel application, while the leading figure gives the nominal carbon content. The vanadium addition is the small but important detail, since it contributes precipitation strengthening and helps hold properties through the tempering cycle without the loss of toughness that a heavier carbon addition would cause.
Vanadium microalloying is also why the grade suits large storage tank construction, where a single shell course may be several metres wide and the plate must combine strength with reliable toughness at the low ambient temperatures found on tank farms.
Delivery Condition and Heat Treatment
| Item | Requirement |
|---|---|
| Delivery condition | Quenched and tempered |
| Tempering temperature | 600 degrees Celsius minimum |
| Tempering temperature after stress relief | 610 degrees Celsius minimum for the final tempering stage |
| Impact test temperature | Minus 20 degrees Celsius |
| Melting route | Oxygen converter steelmaking with vacuum treatment |
| Ultrasonic testing | Sheet by sheet to JB/T 4730.3 or GB/T 2970, acceptance class I |
The two temperature requirements work together. The plate must be tempered at not less than 600 degrees Celsius to develop the intended balance of strength and toughness, and if the finished vessel is given a stress relief heat treatment, the final tempering temperature of the plate must be at least 610 degrees Celsius so that the stress relief cycle does not soften the material below its specified properties. Getting this sequence right is one of the key quality control points on a storage tank project.
Melting Quality and Ultrasonic Testing
The steel is melted in an oxygen converter and given vacuum treatment, a route that lowers the content of hydrogen, nitrogen and other residual gases. Low gas content matters in heavy plate because it reduces the risk of internal defects and improves toughness. To verify that the plate is sound, ultrasonic testing is carried out sheet by sheet in accordance with JB/T 4730.3 or GB/T 2970, with acceptance class I normally specified for tank shell plate. Testing every plate individually rather than on a sampling basis is a deliberate quality decision, since a defect in a shell course cannot be repaired easily after erection.
Application Scope
The primary application is the manufacture of large oil storage tanks and pressure vessels in the petrochemical, gas separation and gas storage and transport industries. The service requirements are a combination of adequate strength and toughness, good weldability and good hot and cold processing behaviour. In tank construction the plate must be formable into large curved shell courses, weldable with automatic and semi-automatic processes at the site, and tough enough to resist brittle fracture when the tank is cooled by its contents or by winter weather.
Fabrication and Quality Control
Forming: cold forming of shell courses is standard, with agreed deformation limits where bends are severe.
Welding: low hydrogen consumables matched to the strength class, controlled heat input and interpass temperature, and qualified procedures for vertical and horizontal site welds.
Heat treatment: stress relief cycles must respect the minimum final tempering temperature so that plate properties are preserved.
Inspection: ultrasonic testing sheet by sheet, mechanical testing in the delivery condition, and simulated post-weld heat treatment tests where required.
Documentation: quality certificate with heat number, chemical analysis, mechanical results and heat treatment records.
Frequently Asked Questions
Q: What is 12MnNiVR used for?
A: Mainly for large oil storage tanks and pressure vessels in petrochemical, gas separation and gas storage and transport service.
Q: What tempering temperature is required?
A: Not less than 600 degrees Celsius, and not less than 610 degrees Celsius for the final tempering stage when stress relief treatment is required.
Q: At what temperature is impact testing performed?
A: At minus 20 degrees Celsius.
Q: How is ultrasonic testing carried out?
A: Sheet by sheet, to JB/T 4730.3 or GB/T 2970, normally with acceptance class I.
Q: How is the steel melted?
A: In an oxygen converter with vacuum treatment, which keeps residual gas content low in heavy plate.






