11MnNiMoDR Low Temperature Pressure Vessel Steel Plate

Jan 15, 2024 Leave a message

What 11MnNiMoDR Plate Is

11MnNiMoDR is a low-alloy steel plate developed for low temperature pressure vessel service. The grade designation follows the Chinese pressure vessel convention: the leading figure gives the nominal carbon content in hundredths of a percent, the letters identify the principal alloying elements, "D" marks low temperature service and "R" stands for pressure vessel. In practice this describes a manganese-nickel-molybdenum chemistry with carbon held low, which is the standard way of buying a plate that must stay tough when a vessel is cooled well below ambient.

The alloying concept is straightforward. Manganese lifts strength and suppresses the ductile-to-brittle transition, nickel improves toughness of the ferrite matrix and reduces the transition temperature further, and molybdenum contributes strength retention and resistance to elevated temperature service. Low carbon keeps the microstructure fine and weldable, so field fabrication does not require exotic procedures.

Standard Framework and Ordering Content

Plates of this family are ordered under GB/T 713.2-2023, the part of the steel plate and strip standard for pressure equipment that covers non-alloy and alloy steels with specified temperature properties. The standard fixes the grade representation, ordering information, dimensions, shape, mass, technical requirements, test methods, inspection rules, packaging, marking and quality certificate content. Dimensional tolerances, surface condition and marking are commonly referenced to the general plate standards as well, and the certificate is issued in line with GB/T 247 for packaging, marking and quality certification.

An enquiry should therefore state the grade, the delivery condition, the plate size range, the impact test temperature and energy level, the ultrasonic testing class and any additional requirements such as simulated post-weld heat treatment of test pieces.

Delivery Condition, Testing and Certification

Delivery condition: normalised, or normalised plus tempered, fixed at order stage according to thickness and the forming route.

Chemical analysis: heat analysis reported on the mill certificate, with restricted phosphorus and sulphur to protect low temperature toughness.

Mechanical testing: tensile properties together with Charpy V-notch impact testing at the specified low temperature, tested in the delivery condition.

Non-destructive testing: ultrasonic testing sheet by sheet where specified, carried out to JB/T 4730.3 or GB/T 2970 with the acceptance class agreed between purchaser and supplier.

Certification: quality certificate with heat number traceability, plus third-party inspection on request.

Fabrication, Welding and Post-Weld Treatment

Nickel-bearing low temperature steels weld well provided the hydrogen level is controlled. Low hydrogen consumables matched to the base metal strength class, clean joint preparation, and preheat with controlled interpass temperature avoid cold cracking in thicker sections. Heat input should be kept within a moderate band so the heat affected zone retains its toughness. Where the plate is cold formed, the deformation limit stated in the order and any requirement for post-forming heat treatment should be respected, and a stress relief treatment after welding can be applied when wall thickness or service conditions make it necessary.

Applications

11MnNiMoDR plate is widely selected for low temperature pressure equipment in petroleum, chemical, power generation and aerospace plants. Typical components include reactors, heat exchangers, cryogenic storage tanks, separation equipment and pipework fittings. The common thread in these applications is a combination of internal pressure and a design metal temperature low enough that ordinary carbon steel would lose notch toughness.

Frequently Asked Questions

Q: What does the designation 11MnNiMoDR mean?

A: The number indicates the nominal carbon content, the letters Mn, Ni and Mo show the main alloying elements, D denotes low temperature service and R indicates pressure vessel application.

Q: Which standard governs 11MnNiMoDR plate?

A: It is supplied under GB/T 713.2-2023 for steel plates and strips used in pressure equipment with specified temperature properties.

Q: In what condition is the plate normally delivered?

A: Normalised, or normalised plus tempered, with the exact condition agreed in the purchase order according to thickness and the intended forming route.

Q: Which non-destructive tests are usually specified?

A: Ultrasonic testing sheet by sheet to JB/T 4730.3 or GB/T 2970 is common, with the acceptance class specified by the purchaser.

Q: Can the plate be supplied with post-weld heat treatment simulation on test pieces?

A: Yes, simulated post-weld heat treatment of mechanical test samples can be agreed so the reported values reflect the condition of the finished vessel.