S355J2G3 appears on a large number of legacy drawings, vessel calculations and bridge specifications produced before the European structural steel standard was restructured. The designation came from the older EN 10025, and its direct successor in the current system is S355J2+N under EN 10025-2, which carries the same 355 MPa minimum yield strength, the same J2 impact class and the same normalized delivery condition. Engineers rarely need to convert a whole design: they need to confirm that the plate offered today is genuinely equivalent, that the chemistry and impact data on the mill certificate meet the original intent, and that any substitution in a different standard is defensible. This article maps S355J2G3 to its equivalents, compares chemical and mechanical data, and sets out the practical substitution checks for legacy projects.
What S355J2G3 Was and What It Maps To Today
S355J2G3 came from the old EN 10025 and encoded four pieces of information: 355 MPa minimum yield strength, J2 impact class with 27 J absorbed energy at -20 °C, and a deoxidation and killing requirement denoted by the letter G with its number. When the standard was reorganised into separate parts, the non-alloy structural grades moved into EN 10025-2 and the delivery condition became an explicit suffix, so the modern designation S355J2+N states the same yield level, the same impact class and the normalized condition directly. For practical purposes the two designations describe the same plate: the modern grade tightens the phosphorus and sulfur limits slightly, which improves consistency but does not change the design values.
Equivalent Grades by Standard
| Standard or region | Equivalent grade | Notes |
|---|---|---|
| EN 10025-2 | S355J2+N | Direct modern designation with normalized delivery condition |
| ASTM, USA | A572 Grade 50 | Similar yield level for construction, impact not mandatory |
| DIN, Germany | ST52-3N | Older designation with comparable low temperature toughness |
| JIS, Japan | SM490YA | Welded structure grade with its own impact requirements |
| GB, China | Q355D | Matches the 355 MPa yield and -20 °C impact level |
| NFA, France | E36-3 | Construction grade of the same strength class |
| UNI, Italy | Fe 510 C | Comparable tensile strength range |
| BS, UK | 50 C | Older designation for welded structures |
Chemical Composition Compared
| Element, max % | S355J2G3, old EN 10025 | S355J2+N, EN 10025-2 | ASTM A572 Gr 50 |
|---|---|---|---|
| Carbon (C) | 0.20 | 0.20 | 0.23 |
| Manganese (Mn) | 1.60 | 1.60 | 1.35 |
| Phosphorus (P) | 0.035 | 0.030 | 0.040 |
| Sulfur (S) | 0.035 | 0.025 | 0.050 |
| Silicon (Si) | 0.55 | 0.55 | 0.40 |
| Copper (Cu) | 0.55 | 0.55 | not specified |
| Nitrogen (N) | 0.009 | 0.012 | not specified |
Mechanical Properties Compared
Values below apply to plate up to 16 mm thick, which is where most legacy drawings sit.
| Property, plate up to 16 mm | S355J2G3 | S355J2+N | ASTM A572 Gr 50 |
|---|---|---|---|
| Yield strength, min (MPa) | 355 | 355 | 345 |
| Tensile strength (MPa) | 490-630 | 470-630 | 450 min |
| Elongation, min (%) | 22 | 22 | 21 |
| Impact energy at -20 °C, min | 27 J | 27 J | not specified |
The strength and toughness values of S355J2G3 and S355J2+N are effectively the same, so the modern grade can be supplied against an old drawing without changing the design. ASTM A572 Grade 50 has a slightly lower minimum yield and no mandatory impact energy requirement, so it is only a strength equivalent and not a toughness substitute.
Substitution Considerations for Legacy Projects
Standard basis: quote the old grade for reference and the current EN 10025-2 grade as the supplied material, and record both on the certificate.
Toughness: confirm that the delivered plate is tested at -20 °C with a minimum of 27 J, because this is the property that a strength-only equivalent does not reproduce.
Delivery condition: check that the +N condition is stated on the mill certificate, since as-rolled plate of the same grade is a different product for design purposes.
Thickness: property values change with thickness, so the equivalence must be re-checked when a legacy plate is replaced by a thicker section.
Low temperature service: where the design temperature is below -20 °C, move to a tougher grade in the same family rather than relying on the basic J2 impact class.
Availability: S355J2+N is stocked in far greater volume than any legacy grade, so it is normally the fastest route to a compliant replacement.
Frequently Asked Questions
Q: What is S355J2G3 equivalent to in the current EN standard?
S355J2+N under EN 10025-2. The two designations describe the same 355 MPa normalized structural steel with 27 J impact energy at -20 °C, with only minor residual element differences.
Q: Can S355J2+N directly replace S355J2G3 on an old drawing?
Yes for design purposes. The strength and toughness values are equivalent, and the modern grade has tighter phosphorus and sulfur limits, so no design change is normally required.
Q: Is ASTM A572 Grade 50 a true equivalent?
It is a close strength equivalent with a 345 MPa minimum yield, but it has no mandatory Charpy impact requirement, so it should not be used where the -20 °C toughness of S355J2G3 is part of the design basis.
Q: What does the G3 in the old designation mean?
It encoded the deoxidation and killing requirement of the old EN 10025 together with the delivery condition. The modern system replaces these coded letters with explicit suffixes such as +N for normalized.
Q: What is the Chinese equivalent of S355J2G3?
Q355D under GB/T 1591 matches the 355 MPa yield level and the -20 °C impact requirement, and dual certified plate is commonly produced for export projects.
Q: Which grade should be used below -20 °C?
Select a tougher grade in the same family with a lower impact test temperature, and verify the required absorbed energy against the governing design code before releasing the plate for fabrication.






