ASTM A612 Steel: Equivalent Grades and Comparison with A516

May 21, 2025 Leave a message

ASTM-A612-A-612M.pdf

What ASTM A612 Covers

ASTM A612 is the specification for carbon steel plates of high strength intended for welded pressure vessels in moderate and lower temperature service. The specification covers a single strength level rather than the four grades of the general pressure vessel plate specification, and the material is a carbon-manganese-silicon steel that is normally supplied in the normalized condition. A612M is the metric companion designation and ASME SA-612 is the designation applied to the same material under the boiler and pressure vessel code, so dual certification to A612, A612M and SA-612 is normal for project supply. The specification is used where a pressure vessel must be built at a lower weight than ordinary carbon plate allows without moving to a quenched and tempered or alloy grade.

Mechanical Properties

Thickness Minimum yield strength Tensile strength Minimum elongation
Under 12.5 mm 345 MPa, 50 ksi 570 to 725 MPa, 83 to 105 ksi 16 %
12.5 mm to 25 mm 345 MPa, 50 ksi 560 to 695 MPa, 81 to 101 ksi 16 %

Tensile testing is performed in the transverse direction, and elongation is measured on the standard gauge length used for plate. The 345 MPa minimum yield, equal to 50 ksi, is the defining property of the grade: it is roughly a third higher than the minimum yield of the common 485 MPa tensile pressure vessel plate, which is why the same design pressure can be met with thinner material. Impact testing is ordered as a supplementary requirement at a stated temperature where the service condition demands it, and normalization is the usual delivery condition because it delivers the toughness that low-temperature service requires.

How A612 Differs from A516 Grade 70

Property ASTM A612 ASTM A516 Grade 70
Minimum yield strength 345 MPa 260 MPa
Tensile range 570 to 725 MPa 485 to 620 MPa
Minimum elongation 16 % 21 %
Typical delivery condition Normalized Normalized or as-rolled, normalized on request
Effect on design Thinner plate for the same pressure Greater thickness, higher ductility

The two specifications are often quoted as alternatives because both are normalized carbon steel plates for welded pressure equipment, but they are different strength classes. A612 trades ductility and toughness margin for strength, so it is selected when weight or wall thickness is the constraint, while the lower-strength specification remains the default where maximum formability and impact margin are required. Substitution in either direction requires the design stress and the impact requirement to be re-checked against the governing code.

Cross-Reference to Other Standards

ASME SA-612 is the same material as ASTM A612 and requires no conversion. In Europe the closest normalized pressure vessel grades are EN 10028-3 P355NH and its low-temperature variant P355NL2, which share the carbon-manganese chemistry and the normalized delivery condition but specify a lower tensile band than A612, so they cannot be regarded as a direct equivalent. In the Chinese system GB/T 713 Q345R has a minimum yield strength of 345 MPa, matching the A612 yield level, but its tensile range of 510 MPa to 640 MPa sits below the A612 band. Statements that A612 corresponds to a 485 MPa tensile pressure vessel plate or to Q345R therefore describe a broad strength class rather than an equivalence, and they should not be used as the basis for a substitution without a documented engineering review of the design stress, the impact test temperature and the permitted thickness range.

Applications and Design Considerations

A612 is used for pressure vessels, accumulators, storage tanks and similar welded equipment where the combination of moderate strength and low-temperature toughness allows a lighter or thinner construction. Typical duties include vessels for liquefied gases, compressed gas storage and process equipment operating in cold climates, where the design temperature falls below the range comfortably covered by ordinary carbon plate. Design work must use the allowable stress values published for the grade in the applicable code rather than the room-temperature tensile strength, and where the equipment is subject to cyclic service the reduced elongation relative to the lower-strength plate should be considered in fatigue assessment. Thickness availability is narrower than for the general pressure vessel grades, so early enquiry with the mill is advisable on large or heavy projects.

Inspection, Certification and Supply

Plates are released against chemical analysis and transverse tensile testing, with Charpy impact testing where ordered, and the results are reported per heat and per test piece position. Ultrasonic examination to ASTM A435, or to ASTM A578 where special application testing is required, is a frequent project stipulation, and dimensional inspection covers thickness, flatness and edge condition against the general requirements specification. Plates are supplied with a mill test certificate at EN 10204 3.1, with third-party witness at 3.2 available for code-stamped equipment, and each plate is marked with the grade designation, heat number and manufacturer identification so that the delivered item can be traced back to the certified results. Where normalized plate is required, the certificate states the heat treatment cycle applied.

Frequently Asked Questions

Q: What is ASTM A612 equivalent to?

A: ASME SA-612 is the same material. EN 10028-3 P355NH and P355NL2 are the nearest normalized European grades, and GB/T 713 Q345R matches the yield level in the Chinese system, but none of them matches the A612 tensile band exactly, so substitution requires a design review.

Q: Is A612 the same as A516 Grade 70?

A: No. A612 has a minimum yield strength of 345 MPa against 260 MPa for A516 Grade 70 and a higher tensile range, but a lower minimum elongation. The two grades are alternatives in the sense that either may suit a welded pressure vessel, not equivalents.

Q: What is the tensile strength of A612 plate?

A: The specified range is 570 MPa to 725 MPa for thickness under 12.5 mm and 560 MPa to 695 MPa for thickness from 12.5 mm to 25 mm, with a minimum yield strength of 345 MPa and a minimum elongation of 16 %.

Q: Why is A612 normally normalized?

A: Normalizing refines the grain structure and delivers the notch toughness required for moderate and lower temperature service, which is the main reason the grade is selected over as-rolled plate.

Q: Where is A612 plate used?

A: In welded pressure vessels, accumulators and storage equipment where the higher yield allows thinner plate and where the equipment operates in moderate to low temperature service, particularly in cold climates and in liquefied gas duty.

Q: What tests accompany an A612 shipment?

A: Transverse tensile testing and chemical analysis as a minimum, Charpy impact testing where ordered, ultrasonic examination to ASTM A435 or A578 where specified, with all results reported on a mill test certificate at EN 10204 3.1.