What Is 16Mo3 Steel?
16Mo3 is a carbon molybdenum pressure vessel steel plate specified in EN 10028-2, the European standard for flat products made of steels for pressure purposes. It contains nominally 0.25 - 0.35 % molybdenum, which is what separates it from ordinary boiler quality carbon steel such as P265GH. The molybdenum addition raises creep strength and improves resistance to hydrogen attack at temperature, so the grade is used for boiler and pressure vessel components that operate hot, from roughly 350 C up to the upper limit of the C-Mo steel family. It is the modern designation that replaced the older German grade 15Mo3 under the withdrawn DIN 17155 standard.
Chemical Composition per EN 10028-2
| Element | Requirement, % | Effect |
|---|---|---|
| C | 0.12 - 0.20 | Strength, hardenability control |
| Si | 0.35 max | Deoxidation |
| Mn | 0.40 - 0.90 | Strength and toughness |
| P | 0.025 max | Toughness control |
| S | 0.010 max | Inclusion control |
| Mo | 0.25 - 0.35 | Creep and hydrogen resistance |
| Cr | 0.30 max | Residual element |
| Ni | 0.30 max | Residual element |
| Cu | 0.30 max | Residual element |
| N | 0.012 max | Free nitrogen control |
Mechanical Properties and Plate Thickness
Property requirements are set against thickness because the cooling rate through the section during rolling and normalising controls the final grain size. Yield strength falls stepwise as the plate gets heavier, and tensile strength is specified at 440 - 590 MPa. Charpy V-notch impact testing is normally specified at +20 C with a minimum average energy of 27 J for the standard delivery condition; testing at a lower temperature is ordered when the equipment is designed for colder operating duty.
| Thickness, mm | ReH min, MPa | Rm, MPa |
|---|---|---|
| up to 16 | 275 | 440 - 590 |
| over 16 - 40 | 270 | 440 - 590 |
| over 40 - 60 | 260 | 440 - 590 |
| over 60 - 100 | 240 | 440 - 590 |
| over 100 - 150 | 220 | 440 - 590 |
Why the Molybdenum Matters
At room temperature 16Mo3 behaves like a slightly stronger grade of boiler plate. The reason it is bought rather than plain carbon steel is what happens above roughly 350 C. Molybdenum in solid solution slows the diffusion processes that drive creep, so the steel keeps a usable design stress at temperatures where carbon steel would have to be thickened or replaced by a low alloy Cr-Mo grade. The same alloying addition raises resistance to hydrogen attack, which is why C-Mo plate is common in hydroprocessing and synthesis service where hydrogen is present at partial pressure and temperature at the same time.
It follows that the corrosion performance of the grade should not be overstated. 16Mo3 is not a stainless or acid resistant material. It resists atmospheric and boiler water environments through coating and water chemistry control, and it resists hydrogen attack and creep at temperature by virtue of its chemistry. For aggressive acid, chloride or wet hydrogen sulphide service, a stainless steel or a clad plate is normally chosen.
Main Uses of 16Mo3 Plate
Boiler shells, drums and headers, where the steel carries saturated steam and hot flue gas temperature simultaneously.
Pressure vessels and reactor shells in chemical and petrochemical plants, including polymerisation reactors and hydrogenation service.
Heat exchanger shells, channels and tube sheets, where hot and cold streams alternate and fatigue at welds must be avoided.
Distillation, rectification and absorption columns and their associated drums in refinery service.
Blast furnace hot blast stove shells and other high temperature process ducting in metallurgical plants.
Autoclaves and leaching vessels in hydrometallurgy, where the design combines moderate pressure with elevated temperature.
Fabrication, Welding and Delivery Conditions
Plate is normally supplied in the normalised or normalised plus tempered condition, and the ordered condition must be respected in fabrication because any subsequent heat treatment changes the mechanical properties that were certified. The grade is readily cut, formed and machined. Welding follows a qualified procedure with controlled heat input; preheat is applied as the section thickness and restraint increase, and post-weld heat treatment is used where the design code requires it for the wall thickness involved.
Delivery conditions available: as rolled, normalised, thermo-mechanically controlled rolled, quenched and tempered.
Supplementary requirements: ultrasonic examination, impact testing at agreed temperatures, Z15, Z25 or Z35 through thickness testing, and third party inspection.
Forming and cutting: flame, plasma and waterjet cutting with dressed edges for fatigue loaded details.
Frequently Asked Questions
Q: What is 16Mo3 steel plate used for?
Boiler shells, drums and headers, pressure vessel and reactor shells, heat exchanger shells and tube sheets, refinery columns and drums, hot blast stove shells and metallurgical autoclaves.
Q: Is 16Mo3 the same as 15Mo3?
The steel family is the same, a C-Mo plate with roughly 0.25 - 0.35 % molybdenum. 16Mo3 is the current EN 10028-2 designation, while 15Mo3 belonged to the withdrawn German standard DIN 17155.
Q: What is the maximum temperature for 16Mo3?
The family is normally applied up to approximately 530 C. The allowable stress at the design metal temperature must always be taken from the pressure vessel code table being used.
Q: Does 16Mo3 have good corrosion resistance?
It has moderate resistance only. The molybdenum improves high temperature creep strength and resistance to hydrogen attack, not resistance to acids or chlorides, so aggressive media require stainless or clad plate.
Q: In what condition is 16Mo3 supplied?
Normalised or normalised plus tempered for boiler and pressure vessel work. As rolled and quenched and tempered plate is available when the application and specification permit.
Q: Can 16Mo3 be welded easily?
Yes, with a qualified procedure and controlled heat input. Preheat increases with plate thickness and joint restraint, and post-weld heat treatment is applied when the relevant design code requires it.



