SB480M Steel Plate Overview
SB480M is a normalized carbon steel plate for boilers and other pressure vessels specified in JIS G3103. The M designation identifies the grade as a normalized, fine-grain material with a minimum yield strength of 295 MPa and a tensile strength range of 490-610 MPa, which places it above the SB450 grade of the same standard. It is chosen for pressure equipment where a combination of higher design stress, stable impact toughness and dependable weldability is required.
Because the plate is normalized rather than quenched and tempered, it retains good ductility for forming shells and heads and behaves predictably when welded with matching carbon-manganese consumables. Cutting and deep processing are offered for SB480M plate from 8 mm to 150 mm thick, supplied as profiled blanks, beveled rings, drilled parts or machined components, each traced to its heat number.
Chemical Composition of SB480M
| Element | Content, % |
|---|---|
| C | 0.12-0.20 |
| Si | 0.15-0.35 |
| Mn | 0.90-1.50 |
| P | 0.030 max |
| S | 0.030 max |
| Ni | 0.30 max |
| Cr | 0.05-0.30 |
| Mo | 0.08 max |
| Cu | 0.30 max |
| Nb | 0.020 max |
| V | 0.020 max |
| B | 0.004 max |
The carbon range is deliberately low and the manganese range wide, which is what allows the grade to reach its strength through a refined normalized structure instead of through high carbon. Silicon provides deoxidation, while niobium, vanadium and boron are restricted to trace levels to keep the heat affected zone tough. Sulphur and phosphorus at 0.030% maximum limit inclusion content, which supports both impact energy and resistance to brittle fracture.
Mechanical Properties and Normalizing
| Property | Requirement |
|---|---|
| Tensile strength | 490-610 MPa |
| Yield strength, min | 295 MPa |
| Elongation, min | 22% |
| Charpy V-notch impact energy at 0 C, min | 27 J |
Plates are supplied normalized, which means the steel is heated above its critical temperature and then cooled in air. Normalizing refines the grain size, removes the banding left by rolling and produces a uniform ferrite-pearlite structure through the thickness. The result is consistent tensile and impact values from plate to plate and from surface to centre, together with low residual stress, so that profiled and formed parts keep their dimensions during machining and fit-up.
Impact Toughness and Low-Temperature Behaviour
SB480M plate is supplied against a Charpy V-notch impact requirement of at least 27 J measured at 0 C on longitudinal specimens. The test is performed on normalized material and confirms that the plate will resist brittle fracture at low ambient temperature, which is the condition that governs pressure equipment during startup, shutdown and cold-weather operation.
Impact energy depends on grain size and on the cleanliness of the steel, so the low sulphur and phosphorus limits and the fine-grain practice used for this grade are directly linked to the impact result reported on the mill certificate. Where a design calls for testing at a lower temperature than 0 C, the applicable construction code and the purchase order define the test temperature and the acceptance value, and plates are tested accordingly.
Cutting Service for 8-150 mm Plate
Flame cutting from 20 mm to 150 mm for contours, openings and weld preparations, with preheat applied to heavy sections to avoid hardening at the cut edge.
Plasma cutting from 8 mm to 60 mm for higher cutting speed and a narrower heat affected zone.
Waterjet cutting where a cold cut is required to preserve toughness right up to the edge.
Edge preparation by CNC beveling and milling for the weld geometry shown on the drawing.
Nesting optimization to control scrap, with remnant plate identified and returned against its heat number.
Cutting parameters are matched to thickness and to the normalized condition of the plate. On heavy sections, slow and steady cutting speeds keep the thermally affected band shallow, so that the edge hardness remains compatible with the welding procedure applied at the joint.
Applications, Inspection and Delivery
Boiler shells, drums and headers
Pressure vessels for chemical, petrochemical and utility plants
Heat exchangers and condensers
Steam drums and pressure piping components
Formed heads and shells produced by rolling and dishing
Inspection covers ultrasonic testing of the plate before cutting where specified, dimensional verification of profiled and formed parts, and visual or penetrant examination of prepared edges. Mill certificates report the chemical analysis, tensile results and the impact test result at 0 C for the heat supplied, and each delivered part carries an identification that links it back to that heat number.
Frequently Asked Questions
Q: What does the M designation mean in SB480M?
It identifies a normalized, fine-grain carbon steel plate grade within JIS G3103, distinguished from the plain SB480 grade by its specified normalized condition and controlled composition.
Q: What are the strength requirements of SB480M?
The plate must reach a tensile strength of 490-610 MPa, a minimum yield strength of 295 MPa and a minimum elongation of 22%.
Q: What impact test applies to SB480M plate?
A Charpy V-notch test on longitudinal specimens with a minimum energy of 27 J measured at 0 C.
Q: Why is SB480M supplied normalized?
Normalizing refines the grain structure and evens out the rolled banding, which delivers consistent strength and impact toughness through the thickness and keeps the plate dimensionally stable during forming and machining.
Q: What is the difference between SB480M and SB450M?
They come from the same JIS G3103 family, but SB480M carries the higher tensile requirement of 490-610 MPa with 295 MPa minimum yield, while the SB450M grade is specified at a lower strength level.
Q: What thickness of SB480M plate can be supplied cut to shape?
Profiling, beveling, drilling and forming are offered from 8 mm to 150 mm, using flame cutting above 20 mm and plasma or waterjet for thinner sections.






