Grade Designation and Standard Basis
S690QL is a high strength steel plate specified in EN 10025-6, the part of the European standard that covers flat products of high yield strength structural steels in the quenched and tempered condition. Every letter in the designation carries meaning. S identifies a structural steel, 690 is the minimum specified yield strength in MPa for the lower thickness range, Q records that the delivery condition is quenched and tempered, and L fixes the Charpy V notch impact test temperature at minus 50 C.
The same grade family in EN 10025-6 uses a further suffix, QL1, for a test temperature of minus 60 C, while Q without L indicates testing at minus 20 C. That convention matters in procurement: a plate ordered as S690Q and a plate ordered as S690QL have the same strength requirement but different toughness verification, so the impact grade has to be matched to the lowest temperature expected in service.
Mechanical Properties and Delivery Condition
The quenched and tempered condition is what produces the strength. After rolling, the plate is austenitized, water quenched and then tempered at a temperature selected to give a tough, tempered martensitic or bainitic structure. Yielding the top of the strength range depends on this thermal cycle rather than on heavy alloying, which is why the composition is kept low in carbon and designed so that the steel remains weldable in spite of its strength.
| Property | S690QL requirement |
|---|---|
| Minimum yield strength | 690 MPa up to 50 mm, stepped down for thicker plate |
| Tensile strength | 770 to 940 MPa |
| Impact test | 30 J minimum at minus 50 C |
| Delivery condition | Quenched and tempered |
| Maximum carbon | About 0.20 percent |
| Optional thickness direction properties | Z15, Z25 or Z35 |
Two ordering options are routinely requested. Plates for welded structures with through thickness stress are ordered with verified thickness direction properties, designated Z15, Z25 or Z35 according to the reduction of area requirement, with the test carried out to the applicable thickness direction standard. Plates for critical equipment are ordered with a specified ultrasonic examination level so that internal quality is verified before fabrication.
Applications
S690QL is used where high strength translates directly into less steel and less weight. Typical applications are mobile crane booms and chassis, excavator and loader structures, mining machinery, concrete pump booms, heavier lifting equipment, bridge structural components, offshore and port handling machinery, and structural parts of vehicles and trailers where the payload benefit justifies the material cost. The grade can also replace thicker sections of ordinary structural steel, which reduces weld volume and transport weight at the same time.
Fabrication, Welding and Quality Control
Cutting is carried out by plasma, laser or water jet where possible, because thermal cutting introduces a heat affected layer that must be removed before welding on highly stressed joints.
Welding uses low hydrogen consumables matched to the strength and toughness of the base metal, with heat input, preheat and interpass temperature controlled to protect the heat affected zone.
Bending and forming are carried out cold where the equipment allows, since hot forming would destroy the quenched and tempered properties unless followed by a fresh quench and temper cycle.
Drilling, machining and edge preparation follow practices that avoid notches and burrs, which are crack initiation sites in high strength plate.
Tensile and impact testing of the delivered plate confirms the grade, with the impact test carried out at minus 50 C for the L condition.
Ultrasonic examination at the agreed level, thickness direction testing for Z grades, and dimensional checks against the standard complete the inspection package.
Certificates record the heat number, the chemical analysis, the heat treatment cycle and the test results, so that the material can be traced into the structure.
Frequently Asked Questions
Q: What does the L in S690QL stand for?
A: It fixes the Charpy V notch impact test temperature at minus 50 C. Without the L, S690Q is tested at minus 20 C, and S690QL1 is tested at minus 60 C.
Q: What is the domestic Chinese equivalent grade?
A: The closest equivalent is Q690E, a quenched and tempered high strength structural steel grade with a comparable strength class, and it is specified in the Chinese standard for high strength structural steel plates.
Q: Can the plate be delivered in the as rolled condition?
A: No. The strength of S690QL is produced by quenching and tempering, and the plate must be delivered in that condition so that the certified properties are present in the material that the fabricator receives.
Q: What are Z15, Z25 and Z35?
A: They are verified thickness direction property classes, defined by the reduction of area measured in a through thickness tensile test. They are ordered for joints where shrinkage stresses act across the plate thickness.
Q: How does welding affect the strength of the plate?
A: The heat affected zone softens relative to the base metal unless the welding procedure controls heat input and interpass temperature. Qualified procedures with matching consumables keep the joint performance within the design requirements.






