S275J2 Within the EN 10025-2 System
S275J2 is one of the S275 qualities of EN 10025-2, the European standard for hot-rolled products of non-alloy structural steels. The designation carries three pieces of information: S for structural use, 275 for the minimum yield strength in MPa at 16 mm and below, and J2 for the impact quality. J2 means the steel is impact tested at -20 °C, while JR is tested at +20 °C, J0 at 0 °C and K2 at -40 °C. Builders choose the J2 quality where a structure is erected or operated in a cold climate and a minimum toughness guarantee at the design temperature is required rather than assumed.
Chemistry and Thickness-Dependent Yield Strength
EN 10025-2 caps the ladle analysis of S275J2 plate at carbon 0.18 % maximum, manganese 1.50 % maximum, phosphorus 0.025 % maximum, sulphur 0.025 % maximum, nitrogen 0.014 % maximum and copper 0.55 % maximum, with the carbon equivalent value held to about 0.40 % on plate over 40 mm. Because non-alloy structural steel relies on ferrite grain size and manganese rather than on alloying for its strength, the guaranteed yield strength falls as the section gets heavier.
| Thickness range | Minimum yield strength | Tensile strength |
|---|---|---|
| Up to 16 mm | 275 MPa | 430-580 MPa |
| 16-40 mm | 265 MPa | 410-560 MPa |
| 40-63 mm | 255 MPa | 400-540 MPa |
| 63-80 mm | 245 MPa | 400-540 MPa |
| 80-100 mm | 235 MPa | 400-540 MPa |
| 100-150 mm | 225 MPa | 380-540 MPa |
Delivery Condition and Testing Options
S275J2 plate is delivered hot rolled by default. When the order calls for a normalized or normalizing-rolled delivery the suffix +N is added, which is common for plate above 80 mm or where a uniform, stress-relieved microstructure is preferred for subsequent machining. Ultrasonic examination can be ordered to acceptance class UT Class 1, UT Class 2 or UT Class 3, where Class 1 is the most demanding and Class 3 the least. Thickness-direction testing can be ordered as Z15, Z25 or Z35, with Z35 giving the highest through-thickness ductility for welded joints that pull the plate apart through its thickness. Both options are usually written onto the mill order together with the sampling frequency, because the same heat can be certified to more than one class.
Cutting and Deep Processing of 8-150 mm Plate
Heavy S275J2 plate is processed with oxy-fuel flame cutting for the thickest sections, plasma cutting for intermediate gauge where a narrower heat-affected zone is wanted, and abrasive waterjet cutting where the edge must be free of thermal effects, for example before a critical machined joint or a subsequent weld on a flame-cut edge. Dimensional and shape tolerances for the cut plate follow EN 10029 for hot-rolled plate. Deep processing commonly includes CNC profile cutting to a nesting drawing, edge beveling for weld preparation, drilling and counterboring, milling of bearing faces, and sawing or machining of pads and brackets. On plate above 80 mm, preheat before flame cutting is controlled to avoid hard, crack-sensitive cut edges, and cut edges intended for welding are dressed or machined to remove oxide and any hardened layer. Parts are usually delivered with a cutting plan and an identification marking that keeps heat number traceability through the finished assembly.
Quality Documentation and Export Packing
Each order is supported by a mill test certificate to EN 10204 3.1 listing chemical analysis, tensile properties, impact energy at -20 °C and the delivery condition, with 3.2 certification or independent third-party inspection available for project work. Ultrasonic examination reports and thickness-direction test results are issued alongside when those options are ordered. Processed parts are stacked and banded with edge protection, marked with the part number and heat number, and can be packed for container loading or supplied as break bulk with lifting points shown on the packing list.
Frequently Asked Questions
Q: Is S275J2 the same as S275JR?
A: No. Both are S275 qualities of EN 10025-2, but S275J2 is impact tested at -20 °C while S275JR is tested at +20 °C, so J2 is used where the design temperature is below freezing.
Q: Why is S275J0+N sometimes written on an order?
A: The +N suffix states that the plate is delivered normalized or normalizing rolled, and the J0 impact quality is tested at 0 °C. It is a different delivery and testing combination from the standard as-rolled S275J2 position.
Q: Which thickness range is normally stocked?
A: Plate from 8 mm to 150 mm is routinely available, with wider mill positions extending beyond 200 mm for heavier structures.
Q: Can S275J2 plate be cut to a nesting drawing?
A: Yes. Flame, plasma and waterjet cutting are all used, and the process is matched to thickness, edge quality requirement and whether the cut edge will be welded.
Q: What does UT Class 1 mean on an S275J2 order?
A: It is the highest of the three ultrasonic examination acceptance classes normally offered, with UT Class 2 and UT Class 3 being progressively less severe.
Q: Is Z-direction testing needed for a normal welded structure?
A: Z15, Z25 or Z35 testing is added where a welded joint transfers load perpendicular to the plate surface and lamellar tearing is a design concern; it is not required on every plate.





