P355NH Pressure Vessel Steel Plate to EN 10028-3

Mar 05, 2024 Leave a message

P355NH is a weldable fine grain steel plate for pressure equipment, specified in EN 10028-3, the part of the EN 10028 series that covers flat products of steels for pressure purposes in the normalized delivery condition. The designation is systematic rather than decorative: P identifies steel for pressure purposes, 355 is the minimum specified yield strength in megapascals at room temperature, N denotes the normalized delivery condition, and H confirms that the steel is supplied with verified properties at elevated temperatures.

Reading the suffix correctly matters when a specification is checked. N refers to normalising, not to corrosion resistance, and H refers to elevated temperature property verification, not to welding. A plate ordered on a misunderstanding of these letters may still be sound steel but will not match the design basis.

Chemical Composition and Mechanical Properties

EN 10028-3 keeps carbon low, generally at or below about 0.20 %, and adds manganese together with micro-alloying elements such as niobium, vanadium, titanium or aluminium to obtain a fine grain structure. Sulfur and phosphorus are limited to low levels for toughness and weldability, and the normalised condition produces a uniform ferritic-pearlitic microstructure.

Property Requirement
Minimum yield strength, thickness up to 16 mm 355 MPa
Tensile strength range 490 to 630 MPa
Elongation after fracture 21 % minimum
Elevated temperature properties Verified values supplied for design use, as required by the H suffix

The mechanical values decrease as thickness increases, so the design pressure and the ordered thickness must be checked together. Impact testing is applied according to the quality class, and the related low temperature classes in the same standard extend the test temperature for cold service.

Delivery Condition, Tolerances and Inspection

Plates are delivered normalized. Dimensional tolerances follow the tolerance standard for hot rolled flat products and the requirements of the EN 10028 series, while ultrasonic testing for internal imperfections can be ordered to a defined EN 10160 class. Because pressure equipment is subject to third party surveillance, documentation is normally a 3.1 certificate to EN 10204 or a 3.2 certificate countersigned by an independent inspector. Additional tests such as through thickness tensile testing or hardness checks can be added where the design code requires them.

Fabrication and Welding Notes

P355NH is readily welded with all common arc processes. A qualified procedure should specify preheat where thickness or restraint demands it, and post weld heat treatment is often applied to relieve residual stress in heavy wall vessels, with the temperature and holding time kept below the level that would impair the normalized microstructure. Cold forming is straightforward, but hot forming requires care because it can alter the normalised condition; where hot forming is unavoidable, the component is usually re-normalised. Cut edges are usually dressed, and machining is uncomplicated at this strength level.

Applications

P355NH is used for storage tanks, pressure vessels, reactors, columns, heat exchangers, gas holders and process pipework in refining, petrochemical, chemical and energy plants. It is also applied to large welded fabrications such as wind turbine towers, penstocks and heavy plant structures where a certified pressure quality steel is required.

Frequently Asked Questions

Q: What does the H in P355NH indicate?

A: It indicates that the steel is supplied with verified properties at elevated temperatures, so that design values may be taken from the standard's high temperature tables for the grade.

Q: Is P355NH the same as P355N?

A: They share the same base chemistry, strength level and normalized delivery condition. P355NH additionally carries verified elevated temperature properties.

Q: Can P355NH be used at low temperature?

A: For sub-zero service the low temperature classes within EN 10028-3 are the appropriate choice, since their impact testing extends to colder test temperatures.

Q: Is post weld heat treatment required?

A: It is not mandatory in every case. It is normally applied to heavy section or highly restrained pressure components, and the cycle must be controlled so that the normalised condition is not degraded.

Q: Which standards govern the tolerances and testing?

A: The EN 10028 series governs the product requirements, dimensional tolerances follow the hot rolled flat product tolerance standard, ultrasonic testing can be specified to EN 10160, and documentation is issued to EN 10204.