Grade Definition and Standard Reference
P265GH is a non alloy steel plate for pressure equipment, specified in EN 10028-2, the European standard for flat products made of steels for pressure purposes with elevated temperature properties. The grade designation carries its identity: P means pressure purpose, 265 is the minimum specified yield strength at room temperature in MPa for the lower thickness range, G indicates that elevated temperature properties are guaranteed, and H confirms that the properties are verified at high temperature as listed in the standard. The material number is 1.0425.
In Chinese plate practice the closest domestic equivalent is the 25MnG boiler grade, and designers often work from both systems when a project is executed to a European code with Chinese fabrication. The plate is a boiler and vessel quality product, meaning it is delivered with a full set of guaranteed properties rather than only a chemical analysis.
Delivery Condition and Mechanical Properties
The normal delivery condition is normalized, marked N on the certificate and on the plate marking. Normalizing gives a uniform ferrite and pearlite microstructure with even grain size, which is why the properties of normalized plate are stable from plate to plate and why the steel can be cold formed into heads and shells without the scatter that can appear in as rolled material.
| Property | Typical EN 10028-2 value |
|---|---|
| Minimum yield strength, thin range | 265 MPa |
| Tensile strength | 410 to 530 MPa |
| Minimum elongation | 22 percent |
| Delivery condition | Normalized, N |
| Elevated temperature properties | Listed in EN 10028-2 up to 400 C |
The GH suffix is the practical value of the grade for boiler work. EN 10028-2 tabulates minimum proof strength values at a series of elevated temperatures, so a designer can verify the allowable stress of a shell or a drum wall at the metal temperature of the duty, not only at room temperature. The near 0.25 percent molybdenum addition, kept within the standard composition limits, helps the steel retain strength at temperature and reduces the tendency to embrittle during long service.
Applications
Plates of this grade are used for the pressure retaining parts of boilers and vessels working at moderate temperature and pressure. Typical applications are steam drum and shell plates, headers, vessel shells and heads, nozzles and reinforcement pads, equipment structural parts, and the pressure boundaries of process equipment in chemical, petrochemical and power plants where a European material specification is required. The good cold bending behaviour supports the manufacture of dished heads, and the controlled carbon and carbon equivalent keep the steel weldable with conventional consumables and standard procedures.
Fabrication, Testing and Supply Practice
Dimensional tolerances for thickness, width, length and flatness follow EN 10029, and the permissible deviations are normally ordered in the standard class unless a tighter class is requested.
Ultrasonic examination of the plate body is carried out to EN 10160 when the order specifies it, with the acceptance class agreed in advance.
Certificates are issued to EN 10204 in the 3.1 form as a minimum, and 3.2 certification with an independent inspection body is available for coded equipment.
Cold forming of heads is followed by stress relief where the design code requires it, and the heat treatment temperature is kept below the range that would reduce the normalized properties.
Welding uses consumables matched to the tensile class of the plate, with heat input and interpass temperature controlled to protect the heat affected zone toughness.
Plates are marked with heat number, grade, standard designation and inspection status so that the material can be traced from the mill certificate to the finished drum or shell.
Storage and handling matter as well. Plates should be kept clear of the ground on timber or steel supports, with edges protected, because surface damage and edge nicks on normalized plate are difficult to remove on thin sections and can become crack initiation points in service.
Frequently Asked Questions
Q: What does the GH in P265GH stand for?
A: G means that elevated temperature properties are guaranteed, and H indicates that the properties are verified at high temperature as listed in EN 10028-2. That is the key difference from a plain room temperature vessel grade.
Q: What is the material number of P265GH?
A: 1.0425. The material number is the numeric designation used in European practice and appears on the certificate together with the grade symbol.
Q: In what condition is the plate delivered?
A: Normalized, identified by the letter N. Normalizing produces uniform grain size and stable mechanical properties, which is important for cold forming and for the reliability of the design values.
Q: What is the domestic Chinese equivalent?
A: The closest boiler grade is 25MnG. Projects that use both European and Chinese specifications usually compare the composition and property tables of the two systems before accepting an equivalence.
Q: How is thickness tolerance handled?
A: Thickness, width, length and flatness tolerances follow EN 10029. Unless the order asks for a tighter class, the standard class of permissible deviations applies.




