Grade Position in the EN 10028-3 System
P355NH is a weldable fine grain steel for pressure purposes specified in EN 10028-3, the part of the European pressure vessel plate standard that covers normalized steels with elevated temperature properties. The material number is 1.0565. The designation follows the same logic as the rest of the family: P for pressure purpose, 355 for the minimum specified yield strength in MPa, N for normalized delivery and H for verified elevated temperature properties.
The grade is a low alloy steel with a fine grain structure obtained through aluminium or microalloying treatment and controlled rolling followed by normalizing. That structure gives a good balance of strength, toughness and weldability at a moderate cost, which explains why the grade is specified in so many process industry projects in Europe and in projects built to European codes elsewhere. Plates are delivered with a minimum yield strength of 355 MPa in the lower thickness range and a tensile strength in the range of 490 to 630 MPa.
Petrochemical and Chemical Equipment
The largest application field is the chemical and petrochemical industry. The grade is used for storage tanks, columns, reactors, heat exchanger shells, separators and process piping components where the fluid is aggressive and the equipment must run for decades between turnarounds. P355NH resists attack by a wide range of acids, alkalis and salt bearing media when it is combined with the correct internal coating or lining, and its toughness means that the vessel wall does not become brittle at the low ambient temperatures that occur during winter shutdowns or in cold climate plants.
Because elevated temperature properties are guaranteed, the same plate can be used for equipment that operates above ambient, including vessels and columns working at moderate temperature where the allowable stress at the design metal temperature is taken from the tables of EN 10028-3.
Pharmaceutical, Food and Cryogenic Service
Three further sectors account for a large share of consumption.
Pharmaceutical industry: reactors, vessels, piping and tanks for active ingredient production, where the pressure boundary must be clean, weldable and capable of being passivated or lined, and where the base metal chemistry must be controlled so that the process stream is not contaminated.
Food industry: storage tanks, conveying equipment, mixing vessels and pipelines built from plate that meets food hygiene requirements when the appropriate surface finish is applied. The normalized fine grain structure gives the consistent forming behaviour that vessel fabricators need.
Cryogenic engineering: equipment that operates at low temperature, including liquefied natural gas storage tanks and cold box structures, where the specified impact toughness of the grade at low temperature is the property that qualifies the steel for the duty.
In all three sectors the plate is delivered with documentation that allows the fabricator and the end user to verify traceability, and the order usually specifies ultrasonic examination and third party inspection in addition to the normal mechanical tests.
Ordering, Welding and Quality Control
Ordering practice is straightforward but has to be complete. The grade symbol, the standard number, the delivery condition N, the thickness range, the required inspection documents and any supplementary requirements such as ultrasonic testing or thickness direction properties are all stated at order stage, because these change the test schedule and the price.
Dimensional tolerances follow EN 10029, usually the standard class, with tighter classes available for special applications.
Ultrasonic examination to EN 10160 is specified when the equipment is a coded pressure vessel, with the acceptance class agreed in writing.
Certificates are issued to EN 10204 3.1, and 3.2 with an independent inspector for code equipment.
Welding is carried out with low hydrogen consumables matched to the base metal class; preheat and interpass temperature follow the thickness and the carbon equivalent agreed in the welding procedure.
Impact testing of the base metal, weld metal and heat affected zone confirms that the low temperature toughness is retained after fabrication.
Because the grade is normalized, any hot forming or stress relief cycle applied during fabrication should be checked against the mill heat treatment so that the final properties still satisfy the design code.
Frequently Asked Questions
Q: What is the difference between P355NH and a plain carbon vessel plate?
A: P355NH carries a guaranteed minimum yield strength of 355 MPa, verified elevated temperature properties, a fine grain normalized structure and a controlled impact level, rather than the limited property suite of a basic commercial quality plate.
Q: Which standard and material number apply?
A: EN 10028-3, material number 1.0565. The standard part number matters because EN 10028-3 covers normalized fine grain steels, not the non alloy grades of EN 10028-2.
Q: Can the grade be used for LNG equipment?
A: Yes, it is used for cryogenic equipment including liquefied natural gas storage tanks, subject to the impact requirements of the applicable design code at the minimum design metal temperature.
Q: Why is the steel normalized?
A: Normalizing produces an even, fine grain microstructure, which gives consistent strength and toughness and reliable cold forming behaviour for heads, shells and other formed parts.
Q: Which inspections are normally ordered with the plate?
A: Mechanical testing of the delivered plate, impact testing at the specified temperature, ultrasonic examination to EN 10160 when required, and inspection documents to EN 10204. Third party inspection is common for coded vessels.






