What SA537CL2 and SA537MCL2 Cover
SA537CL2, written in metric designation form as SA537MCL2, is a heat-treated carbon-manganese-silicon steel plate for pressure vessels covered by the American standard ASTM A537/A537M. The A537 family is issued in three classes: Class 1 is supplied in the normalised condition, while Class 2 and Class 3 are supplied quenched and tempered. Class 2 is the grade most frequently ordered for petrochemical, gas storage and cryogenic equipment because it combines a higher strength level with dependable low-temperature impact toughness.
In trade documents the grade appears as SA537 Class 2, A537CL2, SA537MCL2 or SA537CL2/SA537MCL2. All of these refer to the same plate specification. Material is ordered by thickness, class, edge condition and, where required, supplementary requirements such as Charpy impact testing or ultrasonic examination.
Chemical Composition and Mechanical Properties
The steel is fully killed and produced to fine grain practice. The table below lists the specified chemical limits of the A537/A537M manganese-silicon composition, in percent by mass.
| Element | C | Mn | P | S | Si |
|---|---|---|---|---|---|
| Class 1 | 0.24 max | 0.70-1.35 | 0.035 max | 0.035 max | 0.15-0.50 |
| Class 2 and Class 3 | 0.24 max | 0.70-1.60 | 0.035 max | 0.035 max | 0.15-0.50 |
Tensile requirements differ by class, and the comparison below is the basis on which designers select a class.
| Class | Delivery condition | Minimum yield strength (MPa) | Tensile strength (MPa) | Minimum elongation (%) |
|---|---|---|---|---|
| Class 1 | Normalised | 345 | 485-620 | 22 |
| Class 2 | Quenched and tempered | 415 | 550-690 | 20 |
| Class 3 | Quenched and tempered | 380 | 515-655 | 22 |
Class 2 plate is normally assigned to ASME P-Number 1, Group 2 for welding procedure qualification, which is convenient for fabricators already holding procedures for carbon and carbon-manganese vessel steels.
Delivery Condition and Heat Treatment
Class 2 plate is austenitised, quenched in water and then tempered; the tempering treatment is the step that produces the balance of strength and notch toughness. Because the mechanical properties depend on the heat treatment rather than on alloy content alone, each plate is tested after the final treatment. Impact testing is not a mandatory requirement of the base specification but is ordered as a supplementary requirement for low-temperature service, and ultrasonic examination may be added in the same way. Thickness tolerances, flatness and edge preparation follow the general requirements for rolled plate, so a plate ordered to a nominal thickness is delivered within the permitted minus and plus deviations of the specification.
Typical Applications
Shell and head plate for reaction heat exchangers, separators and spherical tanks
Oil storage tanks, gas storage vessels and liquefied gas tanks
Nuclear reactor pressure shells and other heavy pressure components
Boiler drums and high-pressure water piping in hydropower stations
Turbine volutes and penstock components
Petroleum and chemical production, storage and transport equipment
Fabrication, Welding and Quality Control
Class 2 plate is readily welded by shielded metal arc, submerged arc and gas shielded processes using low-hydrogen consumables matched to the strength level. Preheat and interpass temperature should be selected from the plate thickness and the carbon equivalent of the actual heat analysis rather than from a fixed rule, and a post-weld heat treatment, where the design code requires one, is applied with attention to the tempering temperature of the base plate so that the delivered strength level is not reduced. Cold forming is carried out with generous bend radii, and flame-cut edges are dressed before welding.
Inspection for pressure service normally includes visual and dimensional checking, ultrasonic testing of the plate for laminations when specified, and mechanical testing of a sample from the same heat and treatment lot. Plates are supplied with a material test certificate showing heat number, class, heat treatment condition and the results of tensile testing, so that the fabricator can trace each plate to its test record.
Frequently Asked Questions
Q: What is the difference between SA537CL2 and SA537MCL2?
A: They are the same plate. SA537MCL2 is the metric designation used under the A537/A537M dual-unit standard, while SA537CL2 is written in the inch-pound form. Only the units of the specified values change.
Q: Is SA537 Class 2 the same as SA537 Class 1?
A: No. Class 1 is normalised with a minimum yield strength of 345 MPa, while Class 2 is quenched and tempered with a minimum yield strength of 415 MPa and a higher tensile range.
Q: Does ASTM A537/A537M require impact testing?
A: Impact testing is optional in the base specification and is added as a supplementary requirement. For low-temperature vessels and gas storage equipment it is normally ordered, with the test temperature and absorbed energy agreed at the time of order.
Q: What thickness range is normally available?
A: Class 2 plate is commonly rolled in the 8 mm to 150 mm range depending on width and mill capability, and the strength requirement applies over the thickness range stated in the order.
Q: Can SA537CL2 plate be welded without preheat?
A: Thin plate with a low carbon equivalent can often be welded without preheat, but for heavier sections and higher carbon equivalent values a controlled preheat is recommended to avoid hydrogen cracking.
Q: How is the delivered plate identified?
A: Each plate carries the heat number, grade and class marking, and the accompanying test certificate records the heat analysis, tensile results, heat treatment condition and any supplementary test results.




