EN 10028-3 P460NH Normalized Pressure Vessel Steel Plate

Feb 20, 2024 Leave a message

Where P460NH Fits in the European Standard System

P460NH is a steel plate for pressure purposes covered by EN 10028-3, the part of the European standard that deals with weldable fine grain steels supplied in the normalized condition. The designation can be read directly: P identifies a pressure application, 460 is the minimum yield strength in megapascals for thickness up to 16 mm, N indicates normalized delivery, and H indicates that the grade is rated for elevated temperature service with specified high-temperature proof strength values.

The steel is a low-alloy fine grain steel. It is not a stainless steel and not a precipitation hardening stainless grade. The alloy concept is based on a carbon-manganese foundation to which nitride and carbide forming elements are added, and the combination of normalization with a fine ferritic grain structure is what produces the balance of strength, toughness and weldability.

Chemical Composition

Element Content (percent by mass)
Carbon 0.20 max
Silicon 0.60 max
Manganese 1.00-1.70
Phosphorus 0.025 max
Sulphur 0.015 max
Niobium 0.05 max
Vanadium 0.20 max
Titanium 0.03 max

The total content of the grain refining elements niobium, vanadium and titanium is limited, and the steel is produced with a fine grain practice supported by an aluminium addition or an equivalent treatment, so that the specified grain size and the low-temperature toughness can be achieved consistently.

Mechanical Properties

Property Requirement
Minimum yield strength, t not more than 16 mm 460 MPa
Tensile strength 570-720 MPa
Minimum elongation 17 percent
Impact energy at -20 C 27 J minimum
Delivery condition Normalized

The N designation requires normalized delivery, and the normalized treatment is what allows the microalloying elements to precipitate as fine compounds, giving precipitation strengthening together with grain refinement. The H designation adds elevated temperature proof strength values, which are listed in the standard for design purposes and are used when the equipment operates above ambient temperature.

Ordering Options and Supplementary Requirements

Non-destructive examination can be ordered as a supplementary requirement, with the inspection standard and the acceptance level stated in the contract. Other commonly ordered options include restricted chemical analysis, a specific surface condition, particular edge preparation and tolerances on flatness or thickness. Because EN 10028-3 works together with the general delivery requirements for steel plate, dimension and tolerance questions are settled by reference to those general requirements unless the order specifies otherwise.

Applications

Pressure vessels and reactor shells

Storage tanks for liquids and gases

Boiler components and heat exchanger parts

Process equipment in chemical and petrochemical plants

Penstock and heavy welded structures requiring fine grain toughness

Fabrication and Welding

The grade is a fine grain weldable steel and is welded by all conventional arc processes with consumables matched to the strength level and the service temperature. Preheating is governed by the carbon equivalent, the plate thickness and the joint restraint. Heat input is kept within the range used in the qualified procedure, and where post-weld heat treatment is required by the design code it is performed at a temperature that preserves the normalized properties of the base plate.

Cold forming is carried out with due allowance for springback, and hot forming is followed by normalizing when the design requires the properties of the delivered plate to be restored. Cut edges are dressed before welding, and dimensional inspection covers thickness, flatness and edge squareness.

Frequently Asked Questions

Q: Is P460NH a stainless steel?

A: No. P460NH is a weldable fine grain carbon-manganese pressure vessel steel microalloyed with niobium, vanadium and titanium, and it is covered by EN 10028-3.

Q: What does the H in P460NH mean?

A: The H indicates that the grade has specified elevated temperature proof strength values for design use, in addition to the room temperature requirements.

Q: How is P460NH delivered?

A: In the normalized condition, as required by the N in the designation.

Q: What is the minimum yield strength?

A: 460 MPa for thickness up to 16 mm, with the tensile strength specified in the 570 MPa to 720 MPa range and a minimum elongation of 17 percent.

Q: Can flaw detection be ordered with the plate?

A: Yes. Non-destructive examination is ordered as a supplementary requirement, and the standard and acceptance level are agreed between supplier and purchaser and stated in the contract.

Q: What is the minimum impact energy of the grade?

A: The standard specifies a minimum Charpy absorbed energy of 27 J at -20 C.