ASTM A662 Grade A Low-Carbon Pressure Vessels Steel Plate

ASTM A662 Grade A Low-Carbon Pressure Vessels Steel Plate

Thickness: 6 mm – 300 mm
Width: 1,500 mm – 4,050 mm
Length: 3,000 mm – 15,000 mm
Certification: EN 10204 3.1 / 3.2
Description
Technical Parameters

What is ASTM A662 Gr.A Low Carbon Plate?


 

ASTM A662 Gr.A is a carbon-manganese-silicon (C-Mn-Si) steel plate engineered specifically for welded pressure vessels operating in moderate- and lower-temperature service. It features the lowest carbon limit in the A662 specification family, with maximum carbon content restricted to 0.17%.

Low carbon content is the defining metallurgical characteristic of Grade A. It provides the best weldability and formability among the three grades in the A662 series while maintaining adequate mechanical strength (minimum yield strength of 275 MPa [40 ksi], tensile strength range of 400–540 MPa [58–78 ksi]) to meet a wide spectrum of pressure vessel design requirements. Produced as a fully killed steel (completely deoxidized), A662 Grade A also exhibits a clean, uniform internal microstructure that is critical for reliable fabrication and long-term service performance.

ASTM A662 Grade A Low Carbon Plate

 
ASTM A662 Gr.A PVQ Plate Chemical property

 

Grade C Mn≥ Si P S
ASTM A662 Gr.A 0.17 0.13-0.45 0.84-1.46 0.035 0.035

 

 
ASTM A662 Gr.A PVQ Steel Plate mechanical property

 

Grade

Thickness

Yield

Tensile

Elongation

ASTM A662 Gr.A

mm

Min Mpa

Mpa

Min %

6-50

275

400-540

23%

50-200

275

400-540

20%

 

 

ASTM A662 Gr.A Low-Carbon Pressure Vessels Steel Plate Specification

 

Parameter Range
Thickness 6 mm – 300 mm
Width 1,500 mm – 4,050 mm
Length 3,000 mm – 15,000 mm
Certification EN 10204 3.1 / 3.2

 

Welding Considerations - Core Advantages of ASTM A662 Gr.A Low Carbon Steel Plate

As the lowest carbon grade in the series, ASTM A662 Gr.A offers the widest, most forgiving welding window. Its low Carbon Equivalent (CEV) minimizes susceptibility to heat-affected zone (HAZ) hardening and hydrogen-induced cracking (HICC). Nevertheless, proper procedural controls remain essential for welded joints intended for sub-zero service:

Preheating:

Preheating to 100–150°C (210–300°F) is recommended for plate thicknesses exceeding 50 mm (2 in.). Thinner plates typically do not require preheat due to the low Carbon Equivalent of Gr.A, depending on ambient temperature and joint restraint.

Interpass Temperature:

Interpass temperature should be maintained at ≤ 200℃ (390℉). Excessive interpass temperatures can cause grain coarsening in the heat-affected zone, degrading sub-zero notch toughness.

Heat Input:

Heat input should be restricted to ≤ 35 kJ/cm. Utilizing low-to-moderate heat input welding procedures helps maintain a fine-grained HAZ microstructure required for low-temperature compliance.

Post-Weld Heat Treatment (PWHT):

Depending on plate thickness, joint geometry, and design service conditions, governing codes (such as ASME BPVC Section VIII) may mandate post-weld heat treatment. Thermal stress relief in the 550–650°C (1020–1200°F) range reduces residual welding stresses and tempers the HAZ microstructure.

Why Gr.A Is the Most Weldable Grade in the A662 Series?

Its low carbon content and low Carbon Equivalent mean relaxed preheat requirements, reduced risk of hydrogen cracking, and maximum tolerance for field fabrication conditions-making it the material of choice for complex weldments and site installations where uniform welding conditions are difficult to maintain.

Unsure About Preheat or PWHT Requirements for Your Gr.A Plate?

Our welding engineers can provide Welding Procedure Specification (WPS) guidance tailored to your plate thickness, joint design, and service temperature - at no cost.

Get Welding Guidance →

 

ASTM A662 Gr.A Pressure Vessels Steel Plate Delivery Condition & Heat Treatment

Heat treatment is governed by plate thickness:

Normalizing (mandatory >40mm): plates over 40mm must be normalized at approximately 870–900°C, then air-cooled. Normalizing refines grain structure, homogenizes the microstructure, eliminates residual rolling stresses, and - critically - lowers the DBTT for improved low-temperature toughness.

As-rolled (default ≤40mm): Gr.A plates of 40mm and under are normally supplied as-rolled, the most economical condition.

Optional treatments: normalizing, stress relieving, or both, per application requirements.
Supplementary processing: UT, Z-direction, TMCP, Q+T available.

 

ASTM A662 Gr.A Carbon Steel Plate Applications

Low-temperature pressure vessels - shells, heads, and nozzles for service at -20°C to -60°C

Storage tanks - for moderate low-temperature process storage

Heat exchangers - tube sheets, baffles, and shells

Separators - oil & gas processing equipment requiring low-temperature toughness

Boiler components - drums and pressure parts in moderate/low-temperature boiler service

ASTM A662 Grade A Carbon Steel Plate Applications

 

What GNEE Steel Can Provide for ASTM A662 Grade A?

GNEE Steel is a specialized supplier of pressure vessel and boiler steel plates, with 17 years of export experience to 100+ countries.

Full-Size Stock & Mill Rolling

Grade A plates from 6–300mm thickness - stock in 7 days, mill rolling in 30–50 days.

Charpy V-Notch Impact Testing

CVN reports at -20°C, -40°C, or -60°C included with every order.

Value-Added Processing

Cutting, beveling, drilling, welding prep, and surface treatment - ready for fabrication.

Technical & Welding Support

Metallurgical and welding guidance (WPS) from inquiry through fabrication.

ASTM A662 Grade A Low-Carbon Pressure Vessels Steel Plate service

Send your specifications - thickness, size, quantity, required test temperature, and delivery condition. Receive a detailed quotation within 24 hours.

Request Quote

 

FAQ

Which grade among A662 Grade A, B, and C has the highest carbon content?

Grade C has the highest maximum carbon content among the three.

Grade A: Maximum 0.17% carbon

Grade B: Maximum 0.22% carbon

Grade C: Maximum 0.24% carbon

 

Which grade is more suitable for low-temperature environments: A662 Grade A, B, or C?

ASTM A662 Grade A is generally the most suitable choice for lower-temperature or cryogenic-adjacent notch toughness among the three, though all grades are designed for moderate and lower temperature service.

 

What are the equivalent grades for A662 Grade A, B, and C, respectively?

The closest European standard (EN) equivalents for ASTM A662 (carbon-manganese-silicon steel plates for moderate and lower temperature pressure vessels) are P275NL1 for Grade A, P295GH (or general matching based on composition) for Grade B, and P355NH for Grade C.

 

 
boiler steel plate Products image

 

steel boiler plate

 

 
GNEE group team photo

 

Boiler Plate Steel

 

 
GNEE group customer visit

 

pressure vessel plate

 

 
 
GNEE Group steel exhibition

 

pressure vessel steel plate

 

We have excellent after-sales service. If you have any questions about ASTM A662 Grade A vessel plate, you can contact us and we will reply you within two hours.

 

Hot Tags: ASTM A662 Grade A Low-Carbon Pressure Vessels Steel Plate, China ASTM A662 Grade A Low-Carbon Pressure Vessels Steel Plate manufacturers, suppliers, factory, Pressure Vessel Plate ASTM A516 Gr 70, ASTM A516 Grade 60 Boiler Plate Steel, A537 steel, ASTM A516 Pressure Vessel Carbon Steel Plate, A515 Pressure Vessel Steel Plate, SA302GrD hot rolled boiler steel plate