What Is RINA Grade E420 Steel Plate?
RINA Grade E420 is a high strength shipbuilding steel plate approved by the Italian classification society RINA for use in ships and offshore structures. The symbol follows the classification society convention: the letter E fixes the impact test temperature at -40 °C, and the number 420 gives the minimum yield strength in MPa. The grade therefore combines a strength level well above ordinary hull steel with the low temperature toughness needed for cold climate routes, ice class service and exposed offshore locations.
The plate sits in the same higher strength family as the D and E grades built around a 355 MPa base, but raises yield strength by roughly 18 %, allowing thinner plating and lighter stiffeners for the same design load. That weight saving is valuable in hull structures, decks and superstructures where stability and deadweight capacity are limited.
Chemical Composition of RINA Grade E420
The table gives the maximum ladle analysis values for RINA Grade E420. Carbon is capped at 0.20 %, sulphur and phosphorus at 0.025 % each, and nitrogen at 0.020 %, keeping the steel clean and weldable with standard shipyard consumables.
| Element | Max % |
|---|---|
| C | 0.20 |
| Si | 0.55 |
| Mn | 1.70 |
| P | 0.025 |
| S | 0.025 |
| N | 0.020 |
Because the grade is intended for welded hull construction, the carbon equivalent and the weld crack sensitivity parameter of the ladle analysis are both controlled. Welding procedure qualification normally includes heat affected zone hardness and Charpy testing of the joint, since the higher strength level of this grade makes the heat affected zone more sensitive to hard phase formation than in ordinary hull steel.
Mechanical Properties
| Property | Requirement |
|---|---|
| Minimum yield strength (MPa) | 420 |
| Tensile strength (MPa) | 530-680 |
| Minimum elongation (%) | 18 |
| Impact test temperature | -40 °C |
| Impact testing direction | Longitudinal Charpy V-notch, energy per the applicable classification rule |
The yield to tensile ratio implied by these figures must be checked against the applicable rule as well, because classification societies limit how much of the tensile strength a designer may use at the yield point of higher strength hull grades.
Fabrication and Welding Notes
Cutting: flame, plasma and laser cutting are all used, with parameters controlled to limit edge hardening before welding.
Welding: qualified procedures with controlled heat input, low hydrogen consumables and limited interpass temperature protect the toughness of the joint.
Forming: cold forming is possible within defined radius limits; hot forming, if used, requires a subsequent heat treatment agreed with the classification society.
Inspection: ultrasonic testing, dimensional checks and full traceability of the heat number are typical requirements for hull materials.
Typical Applications
Shipbuilding: hull plating, decks, inner bottoms and superstructures of sea going vessels, where the strength to weight ratio allows thinner sections.
Offshore structures: platforms, oil rigs, jack-up legs and other structures that combine high static loading with fatigue and corrosion exposure.
Other structural components: bridges, buildings and heavy fabricated components that demand superior strength and durability, where the relevant design code accepts a marine grade.
Ice class and cold climate vessels operating in waters where -40 °C toughness is specified.
Deck machinery, cranes and foundations carrying concentrated loads.
Plates are supplied with a works inspection certificate endorsed for hull use, and additional classification society stamping can be arranged for structures covered by a specific class notation.
Frequently Asked Questions
Q: What does the E in RINA Grade E420 mean?
The letter E indicates that impact toughness is certified at -40 °C, the lowest test temperature in the standard shipbuilding grade series.
Q: What is the minimum yield strength of RINA Grade E420?
The minimum yield strength is 420 MPa, with a tensile strength range of 530-680 MPa and a minimum elongation of 18 %.
Q: What are the carbon and manganese limits?
Carbon is limited to 0.20 % maximum and manganese to 1.70 % maximum, with silicon at 0.55 % maximum, phosphorus and sulphur at 0.025 % each and nitrogen at 0.020 %.
Q: Why is Grade E420 specified instead of ordinary hull steel?
It permits thinner plating and lighter stiffeners at the same design load, which raises deadweight capacity and stability, while the -40 °C impact rating suits cold climate and offshore service.
Q: Can RINA Grade E420 be welded in a shipyard?
Yes, provided a qualified procedure is used with controlled heat input, low hydrogen consumables and appropriate preheat for thick sections.
Q: Where is RINA Grade E420 used?
It is used for hull plating and decks of ships, offshore platforms and rigs, ice class and cold climate vessels, and heavy structural components that require high strength with low temperature toughness.



