What Q490R Is and How the Grade Is Named
Q490R is a quenched and tempered high strength steel plate intended for pressure equipment. The grade symbol is built from Chinese practice: the letter Q stands for the yield strength requirement, the number 490 gives the minimum yield strength in megapascals, and the letter R marks the product as steel for pressure vessels and tanks, the service for which the grade is written. The plate is sometimes listed in stock catalogues as a vessel or container plate, meaning plate for pressure and storage vessels rather than for freight containers, and the mechanical and inspection requirements belong firmly to pressure equipment service.
Q490R replaced the earlier grade 07MnMoVR that was defined in the previous generation of the pressure vessel plate standard. It is now covered by GB/T 713.6-2023, the part of the pressure equipment steel plate and strip series that deals with quenched and tempered high strength steel plates. That part of the standard sets out the grade designation, the information to be agreed at ordering, dimensions, shape, weight, technical requirements, test methods, inspection rules, marking and the quality certificate. It applies to plate from 10 mm to 80 mm in thickness.
Delivery Condition and Mechanical Requirements
| Item | Q490R requirement |
|---|---|
| Standard | GB/T 713.6-2023, replacing the former GB/T 19189-2011 grade 07MnMoVR |
| Minimum yield strength | 490 MPa |
| Tensile strength | Approximately 610 MPa to 730 MPa as specified for the grade |
| Elongation | Not less than 17 percent |
| Delivery condition | Quenched and tempered, with tempering temperature not lower than 600 degrees Celsius |
| Thickness range | 10 mm to 80 mm |
Tempering at 600 degrees Celsius or above is a requirement rather than a preference, because it is the treatment that produces the balance of strength and toughness expected from a quenched and tempered pressure steel. The low carbon, low impurity composition with controlled additions is what allows the plate to be welded into a vessel without a post weld treatment that would soften the base metal excessively.
Why Pressure Service Sets the Specification
Pressure equipment differs from a general structure in one important respect: the consequence of a defect is not a maintenance cost but a loss of containment. That is why the chemistry of Q490R controls sulphur and phosphorus far more tightly than a general purpose structural plate of similar strength, and why impact toughness is guaranteed at the service temperature rather than at room temperature alone. The reduced impurity level also improves through thickness ductility, which matters at ring stiffeners, nozzles and other heavily restrained welded details.
Q490R has good mechanical properties and corrosion resistance for its class and will meet the demands of a range of process environments when the appropriate corrosion allowance and, where necessary, a protective lining or coating are used. In the industrial field the grade is widely applied to equipment that operates under pressure and at moderate temperature, and the design calculations follow the pressure vessel design code applicable to the project.
Typical Applications
Pressure vessels and reactors in the petroleum and chemical industries.
Storage tanks and spheres for process gases and liquids.
Boiler components, drums and headers in power stations.
Penstocks, surge tanks and heavy fabricated pipework in hydropower and process plants.
Heat exchanger shells, separator bodies and heavy duty fabricated equipment.
Common to these applications are thick sections, welded nozzles, high restraint and a requirement for documented mechanical properties and non-destructive testing. The plate is normally supplied cut to size with the rolling direction marked, because the direction of the final rolling pass affects both toughness and forming behaviour.
Fabrication, Testing and Documentation
Welding a 490 MPa quenched and tempered pressure steel requires a qualified procedure, low-hydrogen consumables, controlled preheat and a heat input range that keeps the heat affected zone hardness within acceptable limits. Post weld heat treatment is often specified by the design code, and the treatment temperature must remain sufficiently below the tempering temperature of the base plate so that the parent metal properties are not degraded. Edge preparation is by machining or thermal cutting followed by grinding, and the finish of the weld preparation is inspected before assembly.
Inspection for pressure service is thorough. The plate is checked for dimensions and surface condition, ultrasonic testing to GB/T 2970 is standard for thick plate, and mechanical testing covers tensile properties, elongation and impact energy at the specified test temperature. Through thickness properties to GB/T 5313 can be added for plates that will be subject to high Z direction restraint. The documentation package includes the mill certificate with the heat number and full chemical analysis, the mechanical test results, heat treatment records showing the tempering temperature, the ultrasonic test report and a certificate of conformity.
Frequently Asked Questions
Q: Is Q490R a container plate or a pressure vessel plate?
A: It is a plate for pressure equipment and storage vessels. The term container in stock catalogues refers to vessels and tanks, not to freight containers, and the grade requirements come from the pressure equipment steel plate standard.
Q: What did Q490R replace?
A: It replaced the grade 07MnMoVR that was defined in the earlier pressure equipment plate standard. Q490R is now specified in GB/T 713.6-2023 at the same nominal strength level.
Q: Why must tempering be at 600 degrees Celsius or above?
A: The high tempering temperature is what produces the required combination of strength, ductility and toughness and stabilises the microstructure after quenching. It also leaves room for a stress relief treatment below that temperature without softening the plate.
Q: What thickness range is available?
A: The quenched and tempered high strength pressure plate grade is standardised from 10 mm to 80 mm thick. Heavier sections are normally handled by a different grade and design route.
Q: What testing is supplied with the plate?
A: Chemical analysis, tensile and elongation results, impact energy at the specified test temperature, dimension and surface checks, ultrasonic testing for thick plate, heat treatment records and a certificate of conformity, with through thickness testing available if ordered.







