CCSAH620 Ship Plate: AH620 High Strength Marine Steel

Jan 12, 2024 Leave a message

The Ship Steel Grade System Behind AH620

Ship and marine engineering structural steel is classified by use into three groups: general strength steel, high strength steel and ultra high strength steel. Within each group the grade symbol carries two pieces of information. The quality letter sets the impact test temperature and the number sets the minimum yield strength. In the general strength grades, the four letters A, B, D and E apply to the 235 MPa level and correspond to impact testing at plus 20, zero, minus 20 and minus 40 degrees Celsius. The same letters are attached to a strength number in the high strength series, so AH620 combines a 620 MPa minimum yield strength with impact testing at plus 20 degrees Celsius.

The Chinese standard for these products is GB/T 712-2011, which covers structural steel for ships and marine engineering. The grades it defines run from A, B, D and E through AH32, DH32, EH32 and FH32, then AH36 to FH36, AH40 to FH40, the 420, 460, 500 and 550 MPa levels, and finally the 620 and 690 MPa levels as AH620, DH620, EH620, FH620, AH690, DH690, EH690 and FH690. Certification under classification society rules is issued in addition, and the same grade can be supplied under the rules of the major international societies.

Grade Groups and Typical Applications

Group Grades Impact test temperature Typical use
General strength A, B, D, E Plus 20 to minus 40 degrees Celsius Hull plating, bulkheads, non-critical structure
High strength AH32 to FH40 Plus 20 to minus 60 degrees Celsius Deck structures, hatch covers, tanks, stiffened panels
Ultra high strength AH620 to FH690 Plus 20 to minus 60 degrees Celsius Heavily loaded nodes, machinery supports, offshore structure

AH620 sits at the top of the strength range with the mildest impact requirement of that level. It is chosen where the structure is thick, the load is high and the minimum design temperature is not extreme, so that a lower carbon equivalent and an easier welding procedure can be used than for the equivalent D, E or F quality grade. Typical items are deck machinery foundations, superstructure and accommodation block framing, hatch coaming and cover structures, engine room seatings, and reinforced panels in way of heavy equipment.

Mechanical Requirements and Plate Size Range

The minimum yield strength for the 620 MPa level is 620 MPa, and tensile strength is specified as a range above the yield level for the class. Impact testing is carried out at the temperature fixed by the quality letter, which for AH620 is plus 20 degrees Celsius, and the absorbed energy requirement rises with the strength level and the plate thickness. Plates are normally supplied in the quenched and tempered condition, or after thermo-mechanical rolling with tempering, and the surface must be smooth and free from defects that would affect service or coating.

The usual size range for this class is 3 mm to 80 mm in thickness, 1500 mm to 4000 mm in width and 4000 mm to 19000 mm in length. Heavy plate lines extend the thickness capability for the lower strength ship grades to around 250 mm with widths up to about 4020 mm, and similar wide plate is available in the high strength range depending on the mill and the grade. Plate is supplied with cut or sheared edges to order, with restricted dimensional tolerances available for automated fabrication lines.

Certification, Marking and Additional Testing

Mill certificate with heat number, chemical analysis, tensile and impact results against GB/T 712-2011.

Classification society certificate issued under the rules of the society named by the project.

Painted or labelled marking showing the society approval, heat number, grade, specification and dimensions.

Ultrasonic testing to GB/T 2970 or the relevant society requirement for critical plates.

Through thickness properties to GB/T 5313 in Z15, Z25 or Z35 where the connection is heavily restrained.

Restricted thickness, width and length tolerances for automated cutting and welding lines.

Because the plate will be built into a classed structure, the mark on the plate and the certificate in the documentation must match before the material is released to production. A plate that carries the wrong society mark cannot be used in a certified structural item even if its mechanical results are acceptable, and this is a common cause of delay on shipbuilding projects.

Fabrication and Welding Notes

A 620 MPa ship plate needs a qualified welding procedure, low-hydrogen consumables and controlled preheat, interpass temperature and heat input. Fit up should be accurate so that joints are not forced into position, and where the plate is to be formed, allowance is made for the higher springback of a high strength steel. Cutting by plasma or waterjet is preferred for stressed components, while flame cut edges are dressed where fatigue loading applies. Plate surfaces should be protected from mechanical damage during storage and transport because the appearance and coating performance of a high strength plate in a classed structure are inspected at the yard.

For projects that combine several strength levels, mixing grades within one structure is possible but each joint must be qualified for the combination actually used. The welding procedure for a 620 MPa to 355 MPa joint is not the same as for a 620 MPa to 620 MPa joint, and the harder of the two steels governs the preheat requirement.

Frequently Asked Questions

Q: What does AH620 mean?

A: The letter A is the quality grade and corresponds to impact testing at plus 20 degrees Celsius. The number 620 is the minimum yield strength in megapascals, and H indicates a high strength grade. AH620 is therefore a 620 MPa class steel with a mild temperature requirement.

Q: Which standard defines AH620?

A: GB/T 712-2011 defines the grades, mechanical requirements and test methods for structural steel for ships and marine engineering, and it includes the ultra high strength grades up to the 690 MPa level.

Q: How does AH620 differ from EH620?

A: Both are 620 MPa class. AH620 is impact tested at plus 20 degrees Celsius and EH620 at minus 40 degrees Celsius. AH620 is used where the design temperature allows a simpler welding procedure and a lower carbon equivalent steel.

Q: What plate sizes are produced?

A: Thickness from 3 mm to 80 mm, width 1500 mm to 4000 mm and length 4000 mm to 19000 mm as standard, with heavier and wider plate available on heavy plate lines depending on grade.

Q: Why is ultrasonic testing ordered on ship plate?

A: Ultrasonic testing to GB/T 2970 detects internal discontinuities such as laminations and inclusions that would be unacceptable in a welded, loaded structure. It is normally required for plates used in highly stressed positions.