Q355ME Steel Plate: TMCP Low-Alloy High-Strength Structural Steel

Sep 04, 2025 Leave a message

What Is Q355ME Steel Plate?

Q355ME is a low-alloy high-strength structural steel plate specified in GB/T 1591, the Chinese national standard for high strength low alloy structural steels. The designation is read in four parts: Q is the pinyin initial of qu, the character for yield; 355 is the specified upper yield strength in MPa; M is the delivery condition, thermomechanical rolling (TMCP); and E is the quality grade, which fixes Charpy impact testing at -40 °C.

Q355ME takes its strength from controlled rolling and accelerated cooling rather than from quenching and tempering. The result is a fine-grained microstructure with a balanced combination of strength, toughness and weldability, which is why the grade is used so widely in welded load-bearing structures. It can be fabricated with conventional low-hydrogen procedures, and for most structural thicknesses no post-weld heat treatment is needed.

Mechanical Properties of Q355ME Steel Plate

The values below are the minimum requirements of the grade. Yield strength falls as plate thickness increases, because the rolling reduction ratio and the cooling rate change through the section.

Thickness T (mm) Yield strength ReH min (MPa) Tensile strength Rm (MPa)
T ≤ 16 355 470-630
16 < T ≤ 40 345 470-630
40 < T ≤ 63 335 450-610
63 < T ≤ 80 325 440-600
80 < T ≤ 100 325 440-600
100 < T 320 430-590

Two practical points follow from the table. First, a 10 mm plate and a 120 mm plate are not interchangeable at the same design stress, so the thickness bracket has to be stated on the order. Second, the tensile range narrows as the plate becomes thicker, which means heavy plate offers a smaller margin between minimum and maximum tensile strength; that matters when the design relies on a controlled yield-to-tensile ratio.

Chemical Composition of Q355ME

Heat analysis, weight per cent. Ranges are shown where the standard defines both a lower and an upper limit; single values are maxima.

Element Limit (%) Element Limit (%)
C 0.14 max Ti 0.006-0.05
Si 0.50 max Cr 0.30 max
Mn 1.60 max Ni 0.50 max
P 0.025 max Cu 0.40 max
S 0.020 max Mo 0.10 max
Nb 0.01-0.05 N 0.015 max
V 0.01-0.10 Als 0.015 min

The microalloying additions are what make thermomechanical rolling work. Niobium, vanadium and titanium form fine carbonitride precipitates that pin grain growth during rolling, so the plate reaches a 355 MPa yield without a high carbon content. Low carbon and a maximum manganese of 1.60 % keep the carbon equivalent low enough for shop welding, while the aluminium addition ensures a fully killed, fine-grained steel. Phosphorus and sulphur are held at 0.025 % and 0.020 %, which is what supports the -40 °C impact requirement of the E grade.

Delivery Condition, Ultrasonic Testing and Z-Direction Options

The default delivery condition of Q355ME is thermomechanical rolling. Other grades of the same strength class follow different routes: Q355E is delivered hot rolled, and Q355NE is normalized or normalized rolled. The delivery condition should always be stated together with the grade, because it decides the toughness the mill guarantees and the heat treatment the fabricator has to plan for.

Ultrasonic testing: level 1, level 2 or level 3, where level 1 is the most demanding acceptance class and level 3 the least demanding.

Through-thickness properties: Z15, Z25 or Z35, where Z35 is the highest reduction-of-area class and Z15 the lowest; these are tested in the plate thickness direction for welded joints that carry through-thickness strain.

Size and edge options: cut-to-length plate, trimmed or mill edge, and bevel preparation where the plate is to be welded directly after delivery.

Applications and Grade Comparison

Q355ME is used where a welded structure has to carry high load at low ambient temperature. Typical applications include heavy machinery, engineering and construction machinery, chemical machinery, coal mining machinery, nuclear power and hydropower equipment, bridge structures, cranes and lifting equipment, mining machinery, vehicle equipment and steam turbine components.

Compared with the more common Q355B, Q355D and Q355E plates, the ME grade adds two things: a thermomechanical delivery condition instead of as-rolled or normalized supply, and impact testing at -40 °C at the plate's own thickness. Quality grades in this family run from B (+20 °C) through C (0 °C), D (-20 °C) and E (-40 °C) to F (-60 °C), so the grade letter should be selected from the lowest service temperature of the component rather than from habit.

Frequently Asked Questions About Q355ME Steel Plate

Q: What does the M in Q355ME stand for?
M stands for thermomechanical rolling, also written TMCP. The plate reaches its properties through controlled rolling and accelerated cooling instead of a separate heat treatment.

Q: Which standard covers Q355ME steel plate?
GB/T 1591, the Chinese national standard for high strength low alloy structural steels. The grade can be ordered with additional ultrasonic testing and through-thickness requirements.

Q: Is Q355ME the same as Q355E?
No. The chemistry and the strength class are close, but the letter after the yield value describes the delivery condition: Q355E is hot rolled, Q355ME is thermomechanically rolled and Q355NE is normalized or normalized rolled.

Q: What is the minimum yield strength of Q355ME?
355 MPa for thickness up to 16 mm, 345 MPa from 16 to 40 mm, 335 MPa from 40 to 63 mm, 325 MPa from 63 to 100 mm and 320 MPa above 100 mm.

Q: Can Q355ME be welded without preheat?
Low carbon and a controlled carbon equivalent make the grade readily weldable, but the welding procedure still has to be qualified for the actual thickness and joint. Thin plate welded with low heat input often needs no preheat, while heavy sections need preheat, low-hydrogen consumables and a controlled interpass temperature.

Q: Can the plate be supplied with ultrasonic testing and Z-direction properties?
Yes. Ultrasonic testing at level 1, 2 or 3 and through-thickness testing at Z15, Z25 or Z35 can be specified together with the grade and the size of the plate.