NM600 Wear Resistant Steel Plate: Hardness and Uses

Jan 25, 2024 Leave a message

What NM600 Is and Which Standard Covers It

NM600 is a low alloy, high strength wear resistant steel plate. The letters NM stand for the Chinese term for abrasion resistant, and 600 refers to the hardness class in Brinell units. The family is specified in GB/T 24186, which defines wear resistant plates by hardness band rather than by tensile strength, and it runs from NM300 through NM400, NM450, NM500 and NM550 up to NM600, which is the top of the range. Because abrasion resistance scales with hardness, NM600 is selected when the wear mechanism is dominated by sliding or gouging abrasion and the design allows a thinner and lighter component.

Composition, Hardness and Mechanical Behaviour

The steel is a low alloy, low carbon material in which hardenability is obtained from a combination of manganese, chromium, molybdenum and micro-alloying boron, followed by quenching and low-temperature tempering.

Parameter Typical value
C 0.25-0.35 %
Si 0.20-0.60 %
Mn 0.90-1.60 %
Cr / Mo / B added for hardenability, boron typically 0.005 % max
P 0.015 % max
S 0.010 % max
Surface hardness 570-640 HBW
Microstructure tempered martensite with a small amount of retained austenite

Hardness is the acceptance criterion, measured on the plate surface after delivery. Tensile strength of production plate is normally reported well above 1500 MPa because of the tempered martensitic structure, and Charpy impact values at -20 °C typically fall in the 15-30 J band, which is the price paid for the very high hardness. Designers working with NM600 therefore treat it as a wear component rather than as a primary structural member: it resists abrasion, but it does not provide the plastic reserve of a structural steel.

Applications

NM600 is used where abrasive wear sets the maintenance interval: dump truck bed liners and side plates in mining and quarry haulage, crusher jaws, cone and impact liners, transfer chute and hopper liners, shovel and loader bucket wear parts, dozer blade edges, wear pads and skid plates, bunker and silo liners and conveyor skirt boards. It is also used as a composite liner plate, welded onto a structural backing plate so that a thin, very hard facing layer protects a thicker carrier section. Energy and fleet operators choose this grade because the thinner plate reduces vehicle empty weight, which lowers fuel consumption for the same payload.

Cutting, Forming and Welding

Cutting is normally by plasma, waterjet or laser. Thermal cutting creates a hard, brittle edge zone, so the edge is dressed before it is welded or before it is subject to impact load. Bending is possible but requires generous bend radii relative to thickness and, for heavy plate, preheating of the bend line; tight bends and cold forming of narrow radii are avoided because the tempered martensitic structure has little ductility. Welding uses low-hydrogen consumables matched to the application, with preheat in the 100-150 °C range for thicker sections and controlled heat input. It is good practice not to run welds directly across the high-wear face where a smooth wear surface is required, and to weld liners to the carrier through slotted holes or plug welds rather than with long continuous beads that can initiate cracking. Where a liner plate is welded to a structural steel backing, the consumable and the welding sequence are selected to suit the lower strength backing material.

Selection and Quality Control

Grade selection should start from the wear mechanism. High-stress gouging abrasion with heavy impact favours a lower hardness, tougher grade; pure sliding abrasion of fine ore or coal favours NM600. Orders should state thickness and tolerance, hardness test location and method, whether impact testing is required, flatness limits and the required certificate. Plates are supplied with an EN 10204 type 3.1 mill certificate reporting heat analysis, hardness and any supplementary mechanical results, and are marked with heat number and plate identity. Hardness is normally verified on a defined grid across the plate, since a wear plate that is soft over part of its surface will show uneven wear in service.

Frequently Asked Questions

Q: What hardness does NM600 have?

A: The hardness band defined in GB/T 24186 places NM600 at 570-640 HBW measured on the delivered plate surface.

Q: Can NM600 be welded?

A: Yes, with low-hydrogen consumables, controlled heat input and preheat in the 100-150 °C range for thicker sections. The heat-affected zone should be dressed or, where possible, positioned away from the wear face.

Q: Can NM600 be bent or formed?

A: Only with generous bend radii relative to thickness, and heavy plate is usually preheated along the bend line. Very tight radii and cold forming are avoided because of the limited ductility of the tempered martensitic structure.

Q: Should NM600 be used as a structural member?

A: It is intended as a wear component. Where a part must carry primary structural load as well as resist abrasion, it is usually welded or bolted onto a structural steel backing plate.

Q: How is NM600 different from NM400?

A: The difference is the hardness class and therefore the abrasion resistance. NM600 offers roughly a third more hardness than NM400 but with lower impact toughness, so it suits sliding abrasion rather than heavy impact.

Q: What documentation is provided?

A: An EN 10204 type 3.1 mill certificate with heat analysis, surface hardness results and any supplementary tests, plus plate marking traceable to the certificate.