Grade Definition and Standard Basis
NM400 is a wear resistant steel sheet specified under GB/T 24186, the same national standard that covers the NM360 to NM600 series. The number 400 denotes a nominal surface hardness of 400 on the Brinell scale, and the standard requires a delivered hardness of 360 to 440 HBW. Hardness is measured on the rolled surface, so the value that appears on a mill test certificate is a surface value rather than a through thickness average.
In mechanical terms the grade is a quenched and tempered steel: yield strength is significantly higher than that of ordinary low alloy structural plate, and the wear resistance under sliding abrasion is several times that of mild steel in the same service. For buyers, the useful comparison is not only hardness but the combination of hardness, flatness and thickness tolerance, because the plate is usually installed as a replaceable lining.
Hardness, Strength and Thickness Classification
NM400 plate is produced by electric furnace steelmaking with secondary refining, which keeps sulphur and phosphorus low and gives a clean steel with consistent response to heat treatment. Plates are supplied as flat rectangular product, either rolled directly to width or sheared from a wide strip.
| Product group | Thickness band | Typical use |
|---|---|---|
| Thin sheet | below 8 mm, down to 0.2 mm | Light liners, screens, fabricated panels |
| Medium plate | 8 mm to 60 mm | Chute and hopper liners, bucket wear strips |
| Heavy plate | 60 mm to 120 mm | Crusher parts, heavy duty impact liners |
Hardness is held within the 360 to 440 HBW window across the standard thickness range, and the tensile strength of the grade is high enough that the plate can also act as a structural member in lightly loaded equipment. Elongation remains modest, which is why forming is done cold only within generous bend radii.
Delivery States and Through Thickness Options
The standard delivery state for NM400 is quenched and tempered. Normalised and tempered supply, as well as other states agreed at the technical requirement stage, can also be produced when the buyer needs a specific combination of hardness and toughness or a softer condition for machining. Orders that require drilling of thick liners are frequently placed in a softened state so that conventional tooling can be used.
Quenched and tempered: standard wear supply with guaranteed hardness.
Normalised and tempered: better toughness at slightly reduced hardness, used where impact loading is present.
Z-direction quality: Z15, Z25 and Z35 options are available where the plate carries through thickness tensile stress in a welded connection.
Ultrasonic testing and third party inspection can be specified for critical liners.
Typical Application Range
NM400 is the workhorse wear grade. It is used for the liners of transfer chutes and hoppers in coal handling, for truck and loader bucket floors and side plates, for the wear strips of conveyor discharge points, for the body liners of dump trucks, and for the wearing parts of crushers, screens and mixers. In cement and aggregate plants it is common in clinker handling and in the fine crushing circuit. In steel plants it appears in sinter and coke handling equipment and in slag bunkers.
Because the plate is often fixed by welding or by bolted fasteners, users usually ask for plate with good flatness and with the cut edges free of hard, crack sensitive zones. Edge condition and flatness tolerance therefore belong on the purchase specification together with the hardness range.
Fabrication, Cutting and Quality Control
NM400 is cut by plasma, flame, laser or waterjet. Plasma and waterjet give a clean edge and are preferred for liners that are bolted into place, while oxy-fuel cutting is economical for thick plate. Preheating is advisable above roughly 20 mm thickness to avoid a hard edge that can initiate cracks during forming or service. Drilling is easier in the softened delivery state, and countersunk bolt holes are usually drilled after cutting and before installation.
Welding is performed with low hydrogen electrodes or wire, with a moderate heat input and a controlled interpass temperature. Weld size is normally kept as small as the joint allows, because the heat affected zone softens relative to the parent plate and becomes the local wear path in an abrasive stream. Quality control at the mill covers chemical analysis per heat, hardness measurement per plate, dimensional inspection and, where ordered, ultrasonic examination to confirm internal soundness.
Frequently Asked Questions
Q: What is the hardness range of NM400 plate?
A: GB/T 24186 specifies a surface hardness of 360 to 440 HBW for the grade, measured and reported per plate.
Q: Is NM400 the same as a 400 HB structural plate?
A: No. NM400 is a standardised wear grade with a defined hardness range and toughness requirement, not a generic structural plate that happens to measure 400 HBW.
Q: Can NM400 be bent?
A: Yes, within generous bend radii and with a controlled procedure; tight radii are not practical because of the high yield strength of the quenched and tempered condition.
Q: When should Z-direction quality be specified?
A: When the plate is welded into a connection that develops through thickness stress, Z15, Z25 or Z35 quality should be ordered with the corresponding ultrasonic testing.
Q: How is NM400 supplied for drilled liners?
A: A softened delivery state is available so that the plate can be machined and drilled with conventional tooling before installation.
Q: What documentation comes with an export shipment?
A: A mill test certificate with chemical composition, hardness results and heat traceability, plus optional third party inspection and ultrasonic test reports.



