SA537 Class 1 vs Class 2 Steel Plate: Key Differences

Dec 09, 2025 Leave a message

SA537 Class 1 and Class 2: One Chemistry, Two Heat Treatments

ASME SA-537 and ASTM A537 cover heat-treated carbon-manganese-silicon steel plate intended for fusion-welded pressure vessels and boilers. The specification contains two classes. Class 1 plate is supplied in the normalized condition, and Class 2 plate is supplied in the quenched and tempered condition. That processing difference is what separates the two classes in strength, and it is the reason a designer selects one over the other for a given vessel. SA537 is often confused with SA662, which is a separate carbon-manganese-silicon plate specification; inside SA537 the two options are Class 1 and Class 2, and both are covered by the same chemical requirements.

Chemical Requirements

Element Heat analysis Product analysis
Carbon, max 0.24 % 0.24 %
Manganese, 40 mm and under 0.70-1.35 % 0.64-1.46 %
Manganese, over 40 mm 1.00-1.60 % 0.92-1.72 %
Phosphorus, max 0.025 % 0.025 %
Sulfur, max 0.025 % 0.025 %
Silicon 0.15-0.50 % 0.13-0.55 %
Copper, max 0.35 % 0.38 %
Nickel, max 0.25 % 0.28 %
Chromium, max 0.25 % 0.29 %
Molybdenum, max 0.08 % 0.09 %

Class 1 and Class 2 share this single chemistry table, so the alloy design does not change with the class. Manganese is divided into two thickness groups, and each group has a heat analysis range plus a slightly wider product analysis range that allows for segregation during solidification. Phosphorus and sulfur are both capped at 0.025 %, which is what gives the grade its toughness after heat treatment and welding. Silicon is held between 0.15 % and 0.50 % on heat analysis so that deoxidation is complete without sacrificing notch toughness, and the residual elements copper, nickel, chromium and molybdenum are limited to keep the heat-affected zone predictable in heavy pressure equipment.

Tensile Strength by Thickness

Plate thickness SA537 Class 1, ksi (MPa) SA537 Class 2, ksi (MPa)
65 mm and under 70-90 (485-620) 80-100 (550-690)
Over 65 to 100 mm, inclusive 65-85 (450-585) 75-95 (515-655)
Over 100 to 150 mm, inclusive not specified 70-90 (485-620)

Class 2 is the higher-strength option at every thickness. At 65 mm and under it is certified at 550-690 MPa against 485-620 MPa for Class 1, a difference of roughly one strength step. Because tensile strength falls as the plate thickens, a designer working in heavy wall thickness has to read the table against the ordered gauge rather than applying a single value. Class 1 is tabulated up to 100 mm, while Class 2 extends to 150 mm, which makes the quenched and tempered class the practical choice for very heavy vessel shells.

Yield Strength and Elongation

Property SA537 Class 1 SA537 Class 2
Yield strength, 65 mm and under 50 ksi (345 MPa) 60 ksi (415 MPa)
Yield strength, over 65 to 100 mm 45 ksi (310 MPa) 55 ksi (380 MPa)
Yield strength, over 100 to 150 mm not specified 46 ksi (315 MPa)
Elongation in 50 mm, 100 mm and under 22 % min 22 % min
Elongation in 50 mm, over 100 mm not specified 20 % min
Elongation in 200 mm 18 % min not specified

The yield figures follow the tensile pattern and are the numbers most often used in design calculations. Class 2 provides 415 MPa minimum yield up to 65 mm, which is close to a twenty percent advantage over the 345 MPa of Class 1 and is what allows a thinner wall for the same design pressure. Ductility is preserved in both classes: elongation in a 50 mm gauge length is 22 % minimum for Class 1 and for Class 2 up to 100 mm, relaxing to 20 % above that thickness. Class 1 also carries an 18 % minimum over a 200 mm gauge length, a value that is not specified for Class 2. Because these values refer to different gauge lengths, they should not be compared directly with one another.

Heat Treatment, Welding and Applications

Class 1 is normalized, which produces a uniform ferrite and pearlite structure with good toughness and stable properties through the thickness. Class 2 is quenched and tempered, a route that raises strength while retaining toughness but demands closer control of the austenitizing and tempering cycle. In fabrication, both classes are weldable by the common arc processes using consumables matched to the parent plate; Class 2 generally calls for tighter control of heat input, interpass temperature and, where the service demands it, post-weld heat treatment. Welding procedure qualification should always be based on the certified composition and strength of the plate actually supplied.

Oil, gas and petrochemical vessels and reactors: both classes, selected on design pressure and wall thickness.

Boiler drums and heavy pressure parts: Class 1 for moderate thickness, Class 2 for heavy sections.

Storage tanks and spheres: Class 2 where reduced wall thickness lowers total weight.

Service at moderate and lower temperatures: both classes, with impact testing agreed for the design metal temperature.

In practice the choice is a trade-off. Class 1 offers simpler heat treatment, generous ductility and straightforward fabrication. Class 2 delivers higher design stress, thinner walls and lower weight, at the cost of more tightly controlled processing. Where the wall thickness calculations are close to a limit, the higher yield of Class 2 is often what makes the design work.

Frequently Asked Questions

Q: What is the difference between SA537 Class 1 and Class 2?
Class 1 is supplied normalized and Class 2 is supplied quenched and tempered, which gives Class 2 higher tensile and yield strength at every tabulated thickness.

Q: Is SA537 the same as SA662?
No. SA537 and SA662 are separate specifications for carbon-manganese-silicon plate, and the two designations are often confused in enquiries and search terms.

Q: Which class has the higher yield strength?
Class 2, at 415 MPa minimum up to 65 mm, compared with 345 MPa minimum for Class 1 in the same thickness range.

Q: Are the chemical limits different between the two classes?
No. Both classes are covered by one chemistry table, with carbon capped at 0.24 %, phosphorus and sulfur at 0.025 %, and manganese and silicon specified by analysis type.

Q: What thickness range is covered?
Tensile and yield requirements are tabulated up to 100 mm for Class 1 and up to 150 mm for Class 2.

Q: Which class is better for heavy pressure vessels?
Class 2, because the higher yield strength allows a thinner wall and the tabulated requirements extend to 150 mm.