S460N vs S460NL Steel Plate: 460 MPa Fine-Grain Grades Compared

Aug 21, 2025 Leave a message

S460N and S460NL: High Strength Normalized Fine-Grain Steels

S460N and S460NL are weldable fine-grain structural steels supplied in the normalized or normalized rolled condition under EN 10025-3. Both offer a minimum yield strength of 460 MPa, a tensile range of 540 to 720 MPa and a fine grain structure that delivers toughness as well as strength. They differ in one decisive respect: the temperature at which impact toughness is guaranteed, -20 °C for S460N and -50 °C for S460NL.

Because the strength is shared, the selection between them is governed by the lowest service temperature of the structure and by the required section thickness rather than by load capacity.

Grade Naming and Standard Basis

S - structural steel.

460 - minimum yield strength in MPa at thickness up to 16 mm.

N - normalized or normalized rolled delivery condition with impact testing at -20 °C.

NL - normalized or normalized rolled delivery condition with impact testing at -50 °C.

Both grades are supplied as plate, with the tabulated yield strength falling as thickness increases.

Chemical Composition Compared

Element (ladle, max %) S460N (EN 10025-3) S460NL (EN 10025-3)
Carbon 0.20 0.20
Silicon 0.60 0.60
Manganese 1.00 to 1.70 1.00 to 1.70
Phosphorus 0.030 0.025
Sulphur 0.025 0.020
Copper 0.55 0.55
Chromium 0.30 0.30
Nickel 0.50 0.80
Vanadium 0.12 0.20
Niobium 0.05 0.10
Aluminium (min, total) 0.020 0.020

The two analyses are close, but S460NL carries the tighter impurity limits plus higher nickel, vanadium and niobium. Those additions refine the grain further and depress the ductile-to-brittle transition temperature, which is what makes the -50 °C impact guarantee achievable. Both grades are fully killed and aluminium treated.

Mechanical Properties and Impact Toughness

Property S460N (EN 10025-3) S460NL (EN 10025-3)
Minimum yield strength, thickness ≤ 16 mm 460 MPa 460 MPa
Tensile strength 540 to 720 MPa 540 to 720 MPa
Minimum elongation 17% 17%
Impact test temperature -20 °C -50 °C
Impact energy, thickness ≤ 40 mm 30 J minimum 27 J minimum
Carbon equivalent 0.50 max up to 30 mm, 0.53 max above 0.50 max up to 30 mm, 0.53 max above

One point deserves emphasis because it is widely misquoted. The grade is defined by a minimum yield strength of 460 MPa at thickness up to 16 mm, and the tabulated yield value decreases for heavier sections in line with EN 10025-3. A statement that this steel guarantees only 450 N/mm2 does not belong to the S460 designation and should not be used for design.

Weldability, CEV and Applications

Weldability. Both grades are readily welded with shielded metal arc, gas metal arc and submerged arc processes. The carbon equivalent limit of 0.50 maximum up to 30 mm and 0.53 maximum above 30 mm means that preheating and controlled heat input are part of a sound procedure, especially in thick, highly restrained joints. Filler metals are selected to match the 460 MPa strength level with adequate toughness.

Strength to weight. The 460 MPa yield level allows thinner sections than a 355 MPa grade for the same load, reducing self weight and welding volume.

Applications. Typical uses include bridges, offshore platforms and other marine structures, penstocks for hydropower schemes, heavy machinery frames, crane booms and industrial equipment. Both grades also suit pressure-retaining and load-bearing components where a combination of high strength and reliable toughness is required.

Cold service rule. Where the lowest service temperature falls below -20 °C, S460NL should be specified. Above that temperature, S460N is normally the more economical choice and delivers the same strength.

Frequently Asked Questions

Q: What is the difference between S460N and S460NL?
Both are EN 10025-3 normalized fine-grain steels with a 460 MPa minimum yield strength. S460N is impact tested at -20 °C and S460NL at -50 °C.

Q: Is S460NL stronger than S460N?
No. Yield strength, tensile strength and elongation limits are identical. The advantage of S460NL lies entirely in low-temperature toughness.

Q: What is the yield strength of S460N steel plate?
The minimum yield strength is 460 MPa at thickness up to 16 mm, with lower tabulated values as thickness increases according to EN 10025-3.

Q: Can S460N be welded?
Yes. It welds with conventional arc processes, but the carbon equivalent of up to 0.53 in heavy sections requires preheating and disciplined heat input control.

Q: When should S460NL be chosen instead of S460N?
Whenever the lowest service temperature is below -20 °C, for example in cold climate structures, offshore installations and equipment subject to sub-zero operating conditions.

Q: What are the typical applications of S460NL?
Bridges, offshore platforms, penstocks, crane booms and heavy machinery where high strength combines with guaranteed toughness at very low temperature.