General Product Description
The ASTM A709 is the Standard Specification for Structural Steel for Bridges and encompasses carbon, high-strength low-alloy, and quenched and tempered alloy steels used as structural plates in the construction of bridges.
Available Dimensions
|
Grade |
Thickness |
Width |
Length |
|---|---|---|---|
|
50 |
0.1875 - 3.00 |
72 - 120 |
240 - 1200 |
|
50T |
0.1875 - 3.00 |
72 - 120 |
240 - 1200 |
|
50F |
0.1875 - 2.50 |
72 - 120 |
240 - 1200 |
|
50F |
2.51 - 3.00 1) |
72 - 120 |
240 - 1200 |
Mechanical Properties
|
Grade |
Thickness |
Yield strength 1) |
Tensile strength |
Elongation in 2" 2) |
Elongation in 8" 2) |
|---|---|---|---|---|---|
|
50 |
0.1875 - 3.00 |
50 |
65 |
21 |
18 |
|
50T |
0.1875 - 3.00 |
50 |
65 |
21 |
18 |
|
50F |
0.1875 - 3.00 |
50 |
65 |
21 |
18 |
Impact Properties
|
Grade |
Thickness |
Min Longitudinal Average Energy 1) |
Min Longitudinal Individual Value 1) |
Zone 1 Test Temp |
Zone 2 Test Temp |
Zone 3 Test Temp |
|---|---|---|---|---|---|---|
|
50T |
0.1875 - 2.00 |
15 |
10 |
70 oF |
40 oF |
10 oF |
|
50T |
2.01 - 3.00 |
20 |
15 |
70 oF |
40 oF |
10 oF |
|
50F |
0.1875 - 2.00 |
25 |
20 |
70 oF |
40 oF |
10 oF |
|
50F |
2.01 - 3.00 |
30 |
24 |
70 oF |
40 oF |
10 oF |
Chemical Composition
|
Type |
C 1) |
Mn 1) |
P |
S |
Si 2) |
Cu 3) |
V |
Cb |
V+Nb |
|---|---|---|---|---|---|---|---|---|---|
|
1 |
0.23 |
1.35 |
0.030 |
0.030 |
0.40 |
0.20 |
- |
0.005 - 0.05 |
- |
|
2 |
0.23 |
1.35 |
0.030 |
0.030 |
0.40 |
0.20 |
0.01 - 0.15 |
- |
- |
|
3 |
0.23 |
1.35 |
0.030 |
0.030 |
0.40 |
0.20 |
0.01 - 0.15 |
0.005 - 0.05 |
0.02 - 0.15 |
1) Manganese minimum 0.80% for plates over 3/8 inches in thickness; a minimum of 0.50% for plates 3/8 inches and less in thickness. The manganese to carbon ratio shall not be less than 2 to 1. For each reduction of 0.01% below the specified carbon maximum, an increase of 0.06% manganese above the specified maximum is permitted up to a maximum of 1.60%.
2) For plates greater than 1.50 inches in thickness, silcon range shall be 0.15% to 0.40.
3) Copper when specfied shall have a minimum content of 0.20%.
Tolerances
Thickness, width, and length tolerances are in accordance with ASTM A6 requirements. The flatness tolerance for as-supplied product is halfstandard ASTM A6 tolerance.





