Q490R Steel Plate Application Scope in Pressure Equipment

Jan 17, 2024 Leave a message

Grade Definition and Position in the Standard System

Q490R is a quenched and tempered high strength steel plate for pressure equipment. The designation is compact but precise: the letter "Q" refers to the specified minimum yield strength, the figure 490 is that strength in megapascals, and the terminal "R" identifies steel intended for pressure vessels. The grade replaced 07MnMoVR when the quenched and tempered pressure vessel plate family was reorganised, and it sits alongside the low temperature variant Q490DRL1, which adds a guaranteed low temperature impact level.

Plates are produced to GB/T 713.6-2023, the part of the steel plate standard for pressure equipment that is devoted to quenched and tempered high strength steel plates. It specifies grade representation, ordering content, dimensions, shape, mass and technical requirements, together with test methods, inspection rules, packaging, marking and quality certificates. The standard covers quenched and tempered high strength plate with thickness from about 10 mm to 80 mm for pressure bearing equipment, which matches most vessel shell, head and nozzle reinforcement work.

Why Designers Choose a High Strength Vessel Plate

The economic case for Q490R is wall thickness. Raising the yield class from a conventional 345 MPa vessel steel to 490 MPa lets a designer reduce plate thickness for the same design pressure and diameter, which cuts weight, weld volume and fabrication hours. The quenched and tempered treatment delivers that strength with a refined microstructure rather than with a heavy alloy addition, so the plate retains adequate toughness and can still be formed and welded with established shop procedures.

Item Requirement
Delivery condition Quenched and tempered
Specified minimum yield strength 490 MPa
Plate thickness covered 10 mm to 80 mm
Governing standard GB/T 713.6-2023
Marking and quality certificate In accordance with GB/T 247

Application Scope in Detail

The application range follows the strength and toughness profile of the grade. In the petroleum and chemical industries, Q490R is used for reactors, hydrogenation and conversion vessels, heat exchangers, separators and pressure piping components where the combination of pressure and wall economy matters. In the power sector it appears in boiler and pressure parts, station vessels and thick-walled equipment. Storage duties such as spherical tanks, oil and gas tanks and liquefied gas tanks are also common, together with general pressure equipment in fertiliser, coal conversion and gas processing plants.

Because the plate is available across a wide thickness band, fabricators can order the same grade for shells, heads and internal components, which simplifies weld procedure qualification and reduces the number of consumable combinations held in the shop.

Processing, Welding and Quality Control

Forming: cold forming is practical within the deformation limits agreed at order stage; hot forming requires a heat treatment route that restores the quenched and tempered properties.

Welding: low hydrogen consumables matched to the strength class, with preheat and interpass temperature controlled according to thickness and joint restraint.

Thermal cutting: flame or plasma cutting is standard, with cut edges dressed before welding.

Inspection: ultrasonic testing sheet by sheet to JB/T 4730.3 or GB/T 2970 is frequently specified, with the acceptance class stated in the order.

Testing: tensile and impact test pieces are taken in the delivery condition, and simulated post-weld heat treatment can be applied when the finished vessel requires it.

Frequently Asked Questions

Q: What does Q490R mean as a grade name?

A: Q indicates the specified minimum yield strength, 490 is the value in MPa and R identifies steel for pressure vessels.

Q: Which grade did Q490R replace?

A: It replaced 07MnMoVR in the quenched and tempered high strength pressure vessel plate series.

Q: What thickness range does the standard cover?

A: Quenched and tempered high strength pressure equipment plate is covered from about 10 mm to 80 mm thickness.

Q: Why specify a 490 MPa yield class instead of a lower strength vessel steel?

A: The higher yield class allows thinner walls for the same design pressure, which reduces weight, weld volume and fabrication cost.

Q: Is ultrasonic testing included as standard?

A: Ultrasonic testing sheet by sheet to JB/T 4730.3 or GB/T 2970 is available and is normally specified with an agreed acceptance class.