Grade Overview: A Low Temperature Pressure Vessel Plate
15MnNiNbDR is a niobium microalloyed low alloy steel plate for low temperature pressure vessels. The DR suffix marks the steel for cryogenic vessel service. The grade is specified with an impact test temperature of minus 45 degrees Celsius, which places it in the window between ordinary low alloy vessel steels used down to about minus 40 degrees and the nickel bearing steels used at minus 70 degrees and below. Niobium refines the grain structure and supports toughness at low temperature, while the manganese and nickel balance supplies the strength needed to keep shell, head and nozzle thicknesses within practical limits.
Applications follow from that position in the property spectrum: cryogenic pressure vessels, low temperature spherical tanks, high parameter cryogenic cylindrical vessels and cryogenic ethylene spherical tanks. In each case the plate has to combine strength with dependable impact energy at the design metal temperature, and that requirement is the reason the grade exists rather than a plain carbon vessel steel.
Chemical Composition to GB/T 3531
| Element | Requirement (heat analysis, %) |
|---|---|
| C | 0.18 max |
| Si | 0.15 - 0.50 |
| Mn | 1.20 - 1.60 |
| Ni | 0.30 - 0.70 |
| Nb | 0.0015 - 0.04 |
| P | 0.02 max |
| S | 0.008 max |
Two lines in the table matter most in fabrication. The low sulphur limit controls inclusions, which improves both notch toughness and through-thickness ductility in welded joints. The niobium range is a deliberate microalloying step: keep the addition inside its limit and grain refinement improves toughness, while an addition outside it risks either loss of toughness or excessive hardening in the heat affected zone. Carbon, manganese and nickel are balanced to deliver the strength shown in the property table without sacrificing the low temperature behaviour that the grade is bought for.
Mechanical Properties by Thickness Band
| Plate thickness | Yield strength, min (MPa) | Tensile strength (MPa) |
|---|---|---|
| over 10 mm up to 16 mm | 370 | 530 - 630 |
| over 16 mm up to 36 mm | 360 | 530 - 630 |
| over 36 mm | 350 | 520 - 620 |
The table shows the usual pattern for vessel plate: as thickness rises, the required yield strength steps down and the tensile range narrows, because thicker sections cool more slowly and cannot be relied upon to develop the same properties. This is why the thickness band belonging to a specific plate has to match the band quoted in its test report, and why orders placed close to a band boundary should name the band explicitly. It is equally important that the plate is supplied from a heat with the required impact energy at the specified test temperature, since strength alone does not qualify the material for low temperature service.
Delivery Condition, Cutting and Forming
Delivery condition - normalized plus tempered is the standard delivery state. Other conditions are supplied only when agreed and written into the contract, because the delivery condition determines which mechanical property set the certificate reports.
Cutting - flame cutting is routine across the 8 mm to 90 mm range, with light preheating used on thicker sections and in cold workshops; plasma cutting suits internal openings and contours; water jet or machining is chosen where edge metallurgy or the tolerance of the finished part matters more than cutting speed.
Edge preparation - bevels are cut or machined to the geometry required by the qualified welding procedure, and the oxidized, locally hardened layer on a flame cut face is removed before welding.
Forming - cold forming of shell courses and head segments is limited by thickness and by the required radius. Hot forming is possible, but the forming temperature must stay below the tempering temperature range of the steel; if it goes above that range, the part must be re-austenitized and tempered afterwards to restore the specified properties.
Tolerances and records - size tolerances for width, length and thickness follow the hot rolled plate tolerance standard applied, such as GB/T 709, and each plate and cut part should keep a marking that ties it back to the heat number.
Deep Processing and Welding for Cryogenic Service
Because the grade is used in vessel and spherical tank construction, plate is frequently supplied processed to drawing rather than as square plate only. A typical sequence covers nesting and cutting to a cutting plan, beveling and machining of edges, rolling of shell courses, pressing of head segments, drilling of openings, and marking and packing for transport. Nesting parts efficiently reduces waste on low temperature plate, and heat number marking should survive every step so that material certificates remain traceable after fabrication.
Welding follows the rules for low temperature pressure equipment: procedure qualification under the applicable pressure equipment standard, low hydrogen consumables, controlled heat input to protect heat affected zone toughness, preheat for thick sections or low ambient temperature, and impact testing of the weld and heat affected zone at the design metal temperature where the specification requires it. Shell, head and nozzle welds are examined by ultrasonic or magnetic particle methods as the specification demands, and packing, marking and the quality certificate for the plate follow GB/T 247.
Frequently Asked Questions
Q: What is 15MnNiNbDR steel plate used for?
It is used to build low temperature pressure equipment such as cryogenic pressure vessels, low temperature spherical tanks, high parameter cryogenic cylindrical vessels and cryogenic ethylene spherical tanks.
Q: What is the impact test temperature of 15MnNiNbDR?
The grade is specified with an impact test temperature of minus 45 degrees Celsius, which is why it is chosen for the temperature window between ordinary low alloy vessel steels and nickel bearing steels.
Q: Which standard covers 15MnNiNbDR?
The plate is produced to GB/T 3531, the standard for low alloy steel plates for low temperature pressure vessels, and packing, marking and the quality certificate follow GB/T 247.
Q: What is the delivery condition of 15MnNiNbDR plate?
Normalized plus tempered is the standard delivery condition. Any other condition has to be agreed and stated in the contract, because it changes the mechanical property set that is certified.
Q: What thickness range is available for cutting and deep processing?
Plate from 8 mm to 90 mm is cut and processed, by flame, plasma or water jet cutting as the part requires, followed by beveling, forming, drilling and dimensional inspection.
Q: Why must hot formed 15MnNiNbDR parts be re-heat treated?
Hot forming above the tempering temperature range alters the microstructure and reduces the properties certified for the plate, so the part has to be re-austenitized and tempered to restore its strength and low temperature toughness.





