Q420 Steel Plate and the GB/T 1591 Product Family
Q420 is a high strength structural steel plate defined in GB/T 1591, the Chinese standard for high strength low alloy structural steels. The letter Q marks a steel specified by yield strength, 420 is the nominal minimum yield strength in MPa, and the letter that follows the number identifies the quality level and therefore the impact test temperature. Q420B is tested at plus 20 degrees Celsius, Q420C at 0 degrees Celsius, Q420D at minus 20 degrees Celsius and Q420E at minus 40 degrees Celsius. Earlier editions of the standard also listed a Q420A quality level, and that designation may still appear on older drawings and certificates.
The grade is valued for its strength to weight ratio and for its strong all round mechanical properties in the normalized, or normalized and tempered, condition. It is a workhorse plate for large welded structures where a 355 MPa steel would drive an uneconomic increase in section thickness.
Chemical Composition of Q420 Plate
Q420 is a low carbon, microalloyed steel. Carbon, sulphur and phosphorus are limited to protect toughness and weldability, while niobium, vanadium, titanium and aluminium are used to control grain size and to raise strength. The limits below combine the values given in the current and the preceding edition of GB/T 1591; where a single figure is shown, the two editions agree.
| Element | Limit, wt. % |
|---|---|
| C, carbon | 0.20 max |
| Si, silicon | 0.55 max |
| Mn, manganese | 1.70 max |
| P, phosphorus | 0.035 max for B, 0.030 for C and D, 0.025 for E |
| S, sulphur | 0.035 max for B, 0.030 for C, 0.025 for D, 0.020 for E |
| Nb, niobium | 0.05 max current edition, 0.07 max preceding edition |
| V, vanadium | 0.13 max current edition, 0.20 max preceding edition |
| Ti, titanium | 0.05 max current edition, 0.20 max preceding edition |
| Cr, chromium | 0.30 max |
| Ni, nickel | 0.80 max |
| Cu, copper | 0.30 to 0.40 max depending on edition |
| Mo, molybdenum | 0.20 max |
| N, nitrogen | 0.015 max |
Where a niobium, vanadium or titanium addition is used, the sum of the three is normally controlled by the standard rather than each element being added in isolation. Aluminium is also added as a grain refining element in the fully killed steel.
Carbon Equivalent and Weldability
Welding a 420 MPa plate is more demanding than welding a 355 MPa plate, so the standard fixes a carbon equivalent value rather than leaving it to the mill. The values below apply to plate delivered in the hot rolled condition and are based on the smelting analysis.
| Nominal thickness or diameter, mm | CEV, max, % |
|---|---|
| up to 30 | 0.45 |
| over 30 up to 63 | 0.47 |
| over 63 up to 150 | 0.48 |
| over 150 up to 250 | 0.49 |
Because the carbon equivalent rises with thickness, preheat and interpass temperature controls become more important as sections get heavier. A written welding procedure with a qualified procedure test is the normal way to demonstrate that a joint in Q420 satisfies the design requirements.
Mechanical Properties: Yield Strength by Thickness
Grade Q420 is delivered in the hot rolled condition for structural work. Yield strength is specified against thickness bands, and the values fall as the section grows, in line with the slower cooling of heavier plate.
| Thickness or diameter, mm | Yield strength, min, N/mm2 |
|---|---|
| up to 16 | 420 |
| over 16 up to 40 | 410 |
| over 40 up to 63 | 390 |
| over 63 up to 80 | 370 |
| over 80 up to 100 | 370 |
| over 100 up to 150 | 350 |
Tensile strength is specified in two broad bands: for thickness up to 100 mm a range of 520 to 680 N/mm2 applies, and for thickness over 100 mm up to 150 mm the range becomes 500 to 650 N/mm2. These figures keep the yield to tensile ratio within a range that retains ductility.
Mechanical Properties: Elongation
Elongation is specified against thickness and against test direction, and the transverse or vertical direction is the one quoted in most acceptance documents.
| Thickness, mm | Longitudinal, min, % | Transverse, min, % |
|---|---|---|
| up to 40 | 20 | 21 |
| over 40 up to 63 | 19 | 20 |
| over 63 up to 100 | 19 | 20 |
| over 100 up to 150 | 18 | 19 |
Equivalent Grades in Other Standards
Q420 is a Chinese national grade, and designers working to other systems need a cross reference. The table below gives the comparable grades usually cited for the higher quality levels of the grade. Cross references of this kind are indicative: the controlling document remains the standard named on the drawing, and the acceptance tests are the ones that actually decide acceptance.
| System | Comparable standard | Comparable grade |
|---|---|---|
| European | EN 10113-2 and EN 10113-3 series | S420NL and S420ML |
| American | ASTM A572M and ASTM A633M | Gr. 60 and Gr. E |
| Japanese | JIS G3124 | SEV295 and SEV345 |
| Australian | AS 3597 | WR 420 |
Two practical warnings apply to any equivalence table. First, an equivalent grade is not necessarily identical in chemistry, and a steel that matches in yield strength may differ in toughness or in carbon equivalent. Second, a substitution normally requires the approval of the design authority, with the supporting mill certificates attached.
Applications of Q420 Plate
The combination of high yield strength and good toughness makes Q420 a first choice for large welded structures where weight matters. Established uses include:
Hull structures and deck sections of large ships.
Bridge girders, cross bracing and other heavily loaded bridge components.
Power station equipment, including penstocks and support structures.
Medium and high pressure boiler plates and high pressure vessel plate.
Lifting machinery such as crane booms and chassis, and mining machinery frames.
General heavy welded structures where a 355 MPa grade would be too heavily stressed.
For pressure equipment, Q420 is usually ordered with a normalized or normalized and tempered delivery condition and with impact testing matched to the design temperature. For structural work, hot rolled delivery is the normal and most economical route.
Frequently Asked Questions
Q: What does Q420 mean in a steel plate designation?
Q indicates a steel specified by yield strength and 420 is the nominal minimum yield strength in N/mm2, so the plate is intended to reach at least 420 MPa in the thinnest bands.
Q: What is the difference between Q420B, Q420C, Q420D and Q420E?
The letters indicate the impact test temperature: plus 20, 0, minus 20 and minus 40 degrees Celsius respectively. Chemistry limits for phosphorus, sulphur and nitrogen are tightened as the temperature falls.
Q: What is the carbon equivalent limit for Q420 plate?
It is 0.45 % for thickness up to 30 mm, rising to 0.47 % up to 63 mm, 0.48 % up to 150 mm and 0.49 % up to 250 mm, based on the smelting analysis for hot rolled delivery.
Q: Is Q420 equivalent to S420?
The grades are comparable, with S420NL and S420ML of the EN series most often cited for the higher quality levels of Q420, but chemistry and toughness requirements are not identical.
Q: Why does the yield strength of Q420 change with thickness?
Heavier plate cools more slowly after rolling, so the same chemistry produces a slightly coarser structure. The standard therefore reduces the required yield strength in steps as thickness increases.
Q: Can Q420 be welded in heavy sections?
Yes, but the carbon equivalent limit and the preheat controls that go with it must be respected. A qualified welding procedure and controlled heat input are the usual safeguards for thick plate.




