What RINA E690 Plate Is
RINA E690 is an extra high strength shipbuilding steel plate grade approved under the rules of RINA, the Italian classification society for ships and marine structures. In the designation, 690 is the minimum yield strength in MPa and the letter E sets the Charpy V-notch impact test temperature at −40 °C. The grade is the strongest of the standard quenched and tempered hull plate classes, combining high strength with toughness, and it is selected where hull weight reduction and high load bearing capacity matter at the same time.
Because the strength level is high, the material is produced as a low alloy steel, quenched and tempered, and delivered against a certificate that reports both chemistry and mechanical test results for each heat.
Chemical Composition
The maxima below are the levels normally applied to RINA E690 plate in the quenched and tempered condition. Phosphorus and sulphur are kept low to protect toughness at −40 °C and to reduce the risk of lamellar tearing in restrained joints.
| Element | Requirement | Element | Requirement |
|---|---|---|---|
| C | 0.20 % max | Ni | 0.40 % max |
| Si | 0.10–0.55 % | Cr | 0.20 % max |
| Mn | 1.70 % max | Mo | 0.08 % max |
| P | 0.030 % max | Cu | 0.35 % max |
| S | 0.030 % max | Al | 0.020 % min |
| Nb | 0.02–0.05 % | V | 0.05–0.10 % |
| Ti | 0.007–0.05 % |
Crack sensitivity is assessed with Pcm = C + Si/30 + Mn/20 + Cu/20 + Ni/60 + Cr/20 + Mo/15 + V/10 + 5B, and the carbon equivalent with Ceq = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15. Both are reported in percent and are used to establish welding preheat and to confirm that the heat is suitable for the intended joint.
Mechanical Properties
| Grade | Thickness (mm) | Yield strength min (MPa) | Tensile strength (MPa) | Elongation min (%) | Impact energy min at −40 °C |
|---|---|---|---|---|---|
| RINA E690 | 8–260 | 690 | 770–940 | 14 | 46 J |
Elongation is lower than for ordinary hull plate, which is normal for a very high strength quenched and tempered steel, and it means that forming operations must respect tighter bend radii. The impact requirement is verified at −40 °C so that the plate can be used in cold water and low ambient temperature service without a risk of brittle fracture.
Delivery Condition and Supplementary Requirements
Quenched and tempered (Q+T) supply is standard; normalised or thermomechanically controlled processing may be agreed where the application permits.
Ultrasonic examination for internal soundness, ordered for critical hull and offshore details.
Through-thickness testing in the Z direction to Z15, Z25 or Z35 when welded joints transfer tensile strain through the plate thickness.
Charpy V-notch impact testing at the specified temperature, with additional temperatures available on request.
Third-party inspection, and surface preparation such as shot blasting and priming for delivery protection.
Fabrication Practice
Match welding consumables to the 690 MPa strength class so that joint efficiency is retained.
Derive preheat and interpass temperatures from the carbon equivalent and plate thickness of the actual heat.
Control heat input to protect heat affected zone toughness, and avoid excessive single pass energy on thick sections.
Remove any flame cut or hardened edge layer before welding, and inspect edges of thick plate for cracks.
Plan lifting and handling carefully: although thinner plate can be used at this strength level, the material is stiff and less tolerant of careless handling.
Applications
RINA E690 plate is mainly used in shipbuilding projects and offshore structural projects, including highly stressed hull regions of large vessels, primary structural members, deck and bottom plating where thickness reduction is valuable, and heavy offshore fabrications. The grade also suits marine equipment that must operate in cold climates, where a combination of high strength and low temperature toughness is mandatory.
Frequently Asked Questions
Q: What is the yield strength of RINA E690 steel plate?
The grade carries a minimum yield strength of 690 MPa with a tensile strength range of 770–940 MPa and a minimum elongation of 14 %.
Q: What does the letter E mean in this grade?
The letter E specifies that the Charpy V-notch impact test is performed at −40 °C, confirming toughness for cold marine service.
Q: What impact energy is required?
The requirement is a minimum absorbed energy of 46 J at −40 °C, checked together with shear fracture appearance and lateral expansion.
Q: In what condition is the plate supplied?
It is normally supplied quenched and tempered, which develops the required strength and toughness while keeping the alloy content moderate.
Q: Which supplementary tests can be ordered?
Ultrasonic examination, through-thickness Z direction testing to Z15, Z25 or Z35, additional Charpy test temperatures and third-party inspection are all available.
Q: What is RINA E690 plate used for?
Shipbuilding projects and ocean offshore structural projects, especially highly stressed hull members where high strength and low temperature toughness are both necessary.






