EN 10025-6 S690QL Equivalent ASTM Steel: A709 Grade 100 Compared

Dec 03, 2025 Leave a message

S690QL-QUALITY-CERTIFICATE.pdf

What EN 10025-6 S690QL Is

S690QL is a high yield strength structural steel plate produced under EN 10025-6, the European standard for flat products of high yield strength structural steels in the quenched and tempered condition. The designation is read as a minimum yield strength of 690 MPa, a quality class Q, and an impact requirement at low temperature class L. The plate is quenched and tempered, so a low-carbon, micro-alloyed chemistry delivers very high strength together with the toughness needed for welded structures such as mobile cranes, heavy transport equipment, lifting gear and high-load bridge or frame components. The material number for S690QL is 1.8928.

What EN 10025-6 S690QL Is Equivalent To

ASTM A709 Grade 100 is normally treated as the closest ASTM equivalent for EN 10025-6 S690QL, because both grades sit in the same 690 MPa minimum yield strength class and both are used for welded structural plate. Beyond ASTM, a 690 MPa grade of the E690 type is the usual comparison in ISO practice. Equivalence up to now has always been conditional: the two grades are governed by different standards, so thickness range, impact energy class and heat treatment condition must be checked one by one before a substitution is approved.

Chemical Composition

Element, max % EN 10025-6 S690QL ASTM A709 Grade 100
C 0.20 0.26
Si 0.80 0.40
Mn 1.70 0.40 - 0.90
P 0.025 0.04
S 0.015 0.05
N 0.015 -
B 0.005 -
Cr 1.50 -
Cu 0.50 -
Mo 0.70 -
Nb 0.06 per heat analysis
Ni 2.00 -
Ti 0.05 -
V 0.12 -
Zr 0.15 -
Al per heat analysis min per heat analysis

The European grade balances chromium, molybdenum, nickel and boron to reach 690 MPa in the quenched and tempered condition, while the ASTM grade keeps a simpler structural chemistry and adds copper, nickel and chromium only when the option is ordered for atmospheric corrosion resistance. Because the two heat analyses are not identical, a mill certificate from one standard cannot simply be read across to the other.

Mechanical Properties

Property Nominal thickness S690QL (EN 10025-6) A709 Grade 100 (ASTM)
Minimum yield strength Reh 3 - 50 mm 690 MPa 690 MPa
Minimum yield strength Reh 50 - 100 mm 650 MPa -
Minimum yield strength Reh 100 - 150 mm 630 MPa -
Tensile strength Rm 3 - 50 mm 770 - 940 MPa 760 - 895 MPa
Tensile strength Rm 50 - 100 mm 760 - 930 MPa -
Tensile strength Rm 100 - 150 mm 710 - 900 MPa -
Minimum elongation after fracture all ranges 14 % 18 % (2 in. gauge length)
Material number - 1.8928 -

Two differences matter in practice. First, yield strength in the European grade steps down as thickness increases, from 690 MPa through 650 MPa to 630 MPa, because heavy quenched and tempered sections cool more slowly. Second, the elongation values are measured over different gauge lengths, so 14 % under EN 10025-6 and 18 % over 2 in. under ASTM A709 are not directly comparable figures.

Substitution and Fabrication Cautions

Confirm the thickness to be ordered, because the allowable yield strength of S690QL depends on it.

Check the impact test requirement: the L class in S690QL specifies low-temperature toughness, and the design temperature on the drawing must be matched.

Review weldability: high strength quenched and tempered plate demands controlled heat input, preheat and hydrogen-free consumables.

Verify whether the receiving standard requires additional tests such as ultrasonic examination or through-thickness properties.

Record the agreed substitution in the project documentation rather than treating the grades as automatically interchangeable.

FAQ

Q: What is the ASTM equivalent of EN 10025-6 S690QL?
ASTM A709 Grade 100 is generally regarded as the closest ASTM equivalent, since both grades have a minimum yield strength of 690 MPa for welded structural applications.

Q: Is there an ISO equivalent of S690QL?
Yes, a 690 MPa grade of the E690 type is the usual ISO comparison for quenched and tempered structural plate in this strength class.

Q: How thick can S690QL plate be supplied?
The property tables cover nominal thicknesses from 3 mm up to 150 mm, with yield strength reduced to 630 MPa in the 100 - 150 mm range.

Q: What does the QL suffix mean in S690QL?
Q indicates the quenched and tempered delivery condition and L indicates the low-temperature impact toughness class specified in EN 10025-6.

Q: Can S690QL and A709 Grade 100 be welded together?
They can be joined with a qualified welding procedure, but the procedure must account for the higher alloy content and the strength and toughness requirements of both grades.

Q: Why does the yield strength of S690QL decrease with thickness?
Because thicker sections cool more slowly during quenching, so the standard allows a lower guaranteed minimum yield strength for the thicker thickness ranges.