ASTM A572 Grade 50 Equivalent Steels and Plate Supply

Aug 21, 2025 Leave a message

ASTM A572 Grade 50 Within the A572/A572M Specification

ASTM A572/A572M covers high-strength low-alloy structural steel in five grades: 42, 50, 55, 60 and 65, where the number is the minimum yield strength in ksi. Grade 50 is the most widely traded of the five, a columbium-vanadium structural steel with a minimum yield strength of 345 MPa used for welded, riveted and bolted construction, for bridge elements and for general structural plate work. The specification is written around strength, formability and weldability rather than around toughness, so any order that needs low-temperature performance has to add a supplementary impact requirement, which is why Grade 50 plate is usually bought with a stated Charpy test temperature and minimum energy.

Specification Range and Chemistry

Commercial A572 Grade 50 plate is rolled from 8 mm to 300 mm in thickness, with widths from 1500 mm to 4020 mm and lengths from 3000 mm to 27000 mm. Heavier sections are supplied as-rolled, normalized rolled or normalized, and may be vacuum degassed or given a simulated post-weld heat treatment when the fabrication sequence calls for it. The chemistry ceiling is carbon 0.23 % maximum, manganese 1.35 % maximum, phosphorus 0.030 % maximum and sulphur 0.030 % maximum, with silicon 0.40 % maximum up to 40 mm and 0.15-0.40 % above 40 mm. Microalloying with columbium, vanadium or titanium is what develops the strength, so the finished properties depend on the rolling schedule as much as on the analysis.

Thickness Minimum yield strength Minimum tensile strength Minimum elongation
8-50 mm 345 MPa 450 MPa 21 %
50-200 mm 345 MPa 450 MPa 18 %

Equivalent Grades in Other Standards

GB/T 1591 Q345B, the closest Chinese structural equivalent, sharing the 345 MPa minimum yield strength.

EN 10025-2 S355JR, S355J0, S355J2 and S355K2, matched by impact temperature: JR tested at +20 °C, J0 at 0 °C, J2 at -20 °C and K2 at -40 °C.

JIS G3106 SM490A, SM490B and SM490C, the Japanese welded-structure grades, with SM490C carrying the coldest impact test.

AS/NZS 3678-350, the Australian structural plate grade with a 350 MPa minimum yield strength.

What Has to Match When an Equivalent Is Substituted

Yield strength alone is not a substitution criterion. The thickness-dependent yield ladder is the first check, because most equivalent grades step down in strength as plate thickness increases while A572 Grade 50 holds 345 MPa across the common range. The impact test temperature is the second check: a Q345B or S355JR plate at +20 °C is not interchangeable with an order that specifies toughness at -20 °C, for which S355J2 or an equivalent J2 quality is required. Chemistry limits, carbon equivalent value and delivery condition come next, followed by dimensional tolerance, ultrasonic acceptance class and any thickness-direction testing. A substitution that ignores the delivery condition can also change how the plate behaves during cutting and welding.

Plate Supply, Processing and Documentation

Warehouse and mill positions for A572 Grade 50 normally cover thickness from 8 mm to 300 mm, width to 4020 mm and length to 12000 mm or more, with as-rolled, normalized and normalized rolled deliveries available. Plate can be prepared for fabrication by flame or plasma cutting to drawing, edge beveling, drilling, milling and shot blasting. Verification is normally a mill test certificate to EN 10204 3.1 with heat number, chemical analysis, tensile and impact results, and it can be raised to 3.2 or accompanied by independent third-party inspection where a project specification demands it. Ultrasonic examination to an agreed acceptance class and thickness-direction testing to Z15, Z25 or Z35 can be added for weld joints loaded through the plate thickness. Shipment is by container for cut-to-size plate or break bulk for full mill plates, with bundle marking showing grade, heat number and size.

Frequently Asked Questions

Q: What is ASTM A572 Grade 50 used for?

A: It is used for welded and bolted structural work, building frames, bridge components, transmission towers, storage racks and general fabrication where a 345 MPa minimum yield strength is required.

Q: Is Q345B a direct substitute for A572 Grade 50?

A: Q345B of GB/T 1591 is the closest structural equivalent in yield strength, but substitution requires an impact test temperature check and a comparison of chemistry limits and delivery condition before it is accepted.

Q: Is A572 Grade 50 the same as A36?

A: No. A36 has a 250 MPa minimum yield strength and a 400-550 MPa tensile range, so A572 Grade 50 is markedly stronger and allows a lighter section for the same load.

Q: What impact test temperature can be specified on Grade 50 plate?

A: Impact testing is supplementary to A572/A572M, so the test temperature and energy are written into the order; -20 °C and -40 °C positions are common for cold-climate structures.

Q: Can A572 Grade 50 plate be supplied normalized?

A: Yes. Normalized and normalized rolled plate is regularly produced for heavier sections and for applications where a stable, refined microstructure is preferred to an as-rolled one.

Q: How does A572 Grade 50 differ from A709 Grade 50?

A: A709/A709M is a bridge steel specification that adds toughness classes and, in certain grades, weathering chemistry. A572 Grade 50 is the general structural plate specification and does not by itself guarantee bridge toughness requirements.