What Is St52-3 Steel?
St52-3 is a weldable structural steel defined in DIN 17100, the German standard that governed general structural steels in Europe before the EN 10025 series replaced it. The designation carries three pieces of information: "St" stands for structural steel, "52" records the minimum tensile strength class in kgf/mm2, which corresponds to roughly 510 MPa, and the trailing "3" identifies the impact toughness class of the grade. The minimum yield strength is 355 MPa, which is the reason drawings that call out St52-3 are today satisfied with S355JR or S355J2 plate to EN 10025-2.
The practical point for plate buyers is that the yield level and the toughness class must both be matched. A substitution that only looks at the 355 MPa figure can leave a structure short of low-temperature impact performance.
Chemical Composition of St52-3
DIN 17100 controls the heat analysis of St52-3 within the limits listed below. The chemistry is deliberately lean. Strength is obtained from manganese rather than from micro-alloying or quenching, which keeps carbon equivalent low and makes the steel weldable with ordinary consumables.
| Element | Limit, % | Role in the grade |
|---|---|---|
| C | 0.20 max | Baseline strength, hardenability control |
| Si | 0.55 max | Deoxidation |
| Mn | 1.00 - 1.60 | Solid solution strengthening, toughness |
| P | 0.040 max | Capped to protect notch toughness |
| S | 0.040 max | Capped to limit inclusions |
Mechanical Properties of St52-3 Plate
Minimum yield strength decreases as plate thickness increases, because the amount of deformation and the cooling rate through the section both change during rolling. Tensile strength for the standard thickness range is specified at 510 - 680 MPa, with a minimum elongation of 20 % for plate up to 16 mm.
| Thickness, mm | ReH min, MPa | Rm, MPa | Minimum yield in kgf/mm2 |
|---|---|---|---|
| up to 16 | 355 | 510 - 680 | 36 |
| over 16 to 40 | 345 | 510 - 680 | 35 |
| over 40 to 63 | 335 | 490 - 650 | 34 |
| over 63 to 80 | 325 | 490 - 650 | 33 |
| over 80 to 100 | 315 | 490 - 650 | 32 |
Impact testing is carried out on longitudinal Charpy V-notch specimens at -20 C, and the average absorbed energy of a set of three specimens must be at least 27 J. That requirement, and not the tensile range, is what separates St52-3 from an ordinary mild steel such as S235JR.
Welding and Fabrication Behaviour
Because the grade is not quenched and tempered, it tolerates the heat of normal fabrication well. Manual metal arc, submerged arc, gas metal arc and flux cored processes are all used in production, and matching strength consumables such as ER70S-6 wire or an E42 electrode class give sound joints in the common thickness range.
Below roughly 30 mm, preheating is usually not required for unrestrained joints at normal shop temperature.
Heavier sections, high restraint and low ambient temperature call for preheat and interpass control following the heat input guidance of EN 1011-2.
Forming, flame cutting, plasma cutting and machining are routine; edges cut thermally should be dressed before fatigue-loaded service.
Post-weld heat treatment is not normally needed, but it can be applied where a specification demands stress relief.
Typical Applications
Building frames, beams, columns and bracing in commercial and industrial construction.
Bridge girders and deck plates, including welded box sections.
Chassis, subframes and supporting structures for transport equipment.
Machine bases, crane booms and heavy equipment frames.
Storage tanks, penstocks, transmission towers and general fabrication.
Equivalent Grades and How to Specify
St52-3 sits in the same strength family as several current grades, but the equivalences are close rather than exact. The impact class has to be checked before a substitution is accepted.
| Standard | Grade | Comment |
|---|---|---|
| EN 10025-2 | S355J2 | Matches the 355 MPa yield and the -20 C impact class |
| EN 10025-2 | S355JR | Same strength, impact class at +20 C only |
| GB/T 1591 | Q355B | Same yield level in the Chinese system |
| GB/T 1591 | Q355D | If a lower impact test temperature is required |
| ASTM A572/A572M | Grade 50 | Similar strength, different chemistry limits, not identical |
When replacing St52-3 with S355JR, confirm whether the original DIN 17100 callout relied on the -20 C toughness class of the "3" suffix. Where it did, S355J2 is the correct substitution rather than S355JR. Plate is normally supplied as rolled, normalised or normalised rolled, and ultrasonic examination, Z-direction testing and third-party inspection can be added as supplementary requirements.
Frequently Asked Questions
Q: Is St52-3 still a valid steel grade?
DIN 17100 has been withdrawn, so St52-3 is no longer a current standard designation. It survives on older drawings and in maintenance work, and the modern route is to convert the callout to the EN 10025-2 grade with the equivalent impact class.
Q: What EN 10025-2 grade replaces St52-3?
S355J2 is the direct replacement when the -20 C impact requirement is to be retained. S355JR is acceptable only where impact testing is specified at +20 C.
Q: What is the Chinese equivalent of St52-3?
Q355B to GB/T 1591 is the closest domestic grade, since both target a 355 MPa minimum yield. Confirm the plate thickness range and the required impact class before releasing the material.
Q: What is the difference between St52-3 and ordinary mild steel?
Strength and toughness. St52-3 delivers a 355 MPa minimum yield against about 235 MPa for S235JR, and it also carries a guaranteed Charpy energy at -20 C.
Q: At what thickness does the yield strength of St52-3 fall?
Above 16 mm. Minimum yield steps down through 345, 335, 325 and 315 MPa as thickness increases to 100 mm.
Q: Can St52-3 be welded without preheating?
Yes for moderate thickness at normal shop temperature. Preheating is applied to heavy sections, highly restrained joints and cold working conditions, with heat input controlled in line with EN 1011-2.



