S355 Steel at a Glance: Standard Basis and Grade Coding
S355 is a weldable structural steel specified in EN 10025-2. The designation follows the European convention: the letter S identifies structural steel, and the number 355 gives the minimum yield strength in megapascals for the thinnest plate range. For plate up to 16 mm thick, EN 10025-2 requires a minimum yield strength (ReH) of 355 MPa and a tensile strength range (Rm) of 470-630 MPa. Both figures step down gradually as thickness increases, which is why heavy plate carries a lower guaranteed yield than the same grade in thin sections.
The toughness sub-class is the second half of the designation. S355JR and S355J0 are verified at +20 °C and 0 °C respectively, S355J2 must deliver at least 27 J of Charpy V-notch energy at -20 °C, and S355K2 raises that requirement to 40 J at -40 °C. Strength is set by the number; the lowest service temperature is set by the letter.
Advantage 1: More Strength for Less Steel Weight
Against the general-purpose S235 class, S355 provides around 120 MPa of additional guaranteed yield strength. A designer can either reduce plate thickness for an unchanged load case or keep the section and work at a higher allowable stress, which cuts steel consumption, dead load and often the cost of the finished structure. The saving propagates into fabrication: thinner plate means smaller weld volumes, fewer passes and shorter handling times.
| Property | S235 (EN 10025-2) | S355 (EN 10025-2) |
|---|---|---|
| Minimum yield strength, t ≤ 16 mm | 235 MPa | 355 MPa |
| Tensile strength range, plate thickness | 360-510 MPa | 470-630 MPa |
| Best low-temperature sub-grade | S235J2: 27 J at -20 °C | S355K2: 40 J at -40 °C |
| Typical applications | Light framing, general fabrication | Bridges, cranes, vehicle frames, heavy machinery |
Because the two grades belong to the same weldable structural family and are supplied with comparable carbon and manganese levels, upgrading a design from S235 to S355 normally requires no change of process beyond re-qualifying the welding procedure for the higher strength class.
Advantage 2: Reliable Energy Absorption and Impact Resistance
The guaranteed Charpy V-notch energy is what separates a structural grade from a material that is merely strong. S355 with a resilience of at least 27 J at the specified test temperature can absorb substantial energy before fracture, so it resists sudden dynamic loading far better than a brittle high-carbon alternative. That property is especially valuable in vehicle construction, where frame members and chassis components must withstand collisions and repeated dynamic forces without shattering.
The sub-grade range lets the buyer match toughness to the coldest expected service condition instead of over-specifying. S355J2 covers most outdoor structures in temperate climates, while S355K2 is selected for cold-store racking, northern infrastructure and equipment exposed to severe winter temperatures. Matching the letter to the real design temperature keeps the purchase economical without trading away safety.
Advantage 3: Predictable Weldability and Fabrication Behaviour
S355 is metallurgically restrained: carbon content is kept low, and micro-alloying plus controlled rolling deliver the strength without creating a brittle microstructure. Carbon equivalent values remain in a range that suits conventional arc processes - manual metal arc, MIG/MAG, submerged arc and flux-cored - with only routine preheat for thick or highly restrained joints.
Delivery condition options: as-rolled, normalized (S355J2+N / S355N) and thermo-mechanically rolled (S355M / S355ML).
Forming: the grade bends and rolls readily; normalized stock is preferred when hot forming is followed by no further heat treatment.
Through-thickness quality: Z15, Z25 and Z35 options control lamellar tearing in heavily restrained welded joints.
Documentation: plates are commonly supplied with inspection documents to EN 10204 3.1.
The low carbon equivalent of the thermo-mechanically rolled variants also lowers the preheat requirement, which shortens fabrication cycles on large welded assemblies.
Advantage 4: Wide Availability and Processing Options
S355 is one of the most widely stocked structural grades, available as plate from roughly 3 mm to more than 200 mm in thickness, as well as in sheet, strip and sections. That availability keeps lead times short and makes the grade easy to combine with downstream processing such as abrasive cutting, laser cutting, drilling, beveling, bending and machining to drawing.
In summary, the advantages of S355 come from a balanced package rather than a single peak value: 355 MPa of guaranteed yield strength, defined impact toughness down to -40 °C, weldability that does not demand exotic procedures, and a supply base broad enough to support large fabrication programmes. For most static and dynamic structural duties, it is the default choice between S235 and the higher-strength quenched and tempered grades.
Frequently Asked Questions
Q: Is S355 the same as S355JR?
No. S355 identifies the strength family, while JR, J0, J2 and K2 define the Charpy impact test temperature and minimum energy. S355JR is the basic ambient-temperature option and S355J2 the most common cold-service option.
Q: What is the minimum yield strength of S355 steel?
EN 10025-2 sets 355 MPa as the minimum yield strength for plate up to 16 mm thick. The guaranteed value decreases for thicker sections, so the applicable figure must be read from the thickness table of the standard.
Q: Can S355 be welded without preheat?
Thin, lightly restrained joints in low carbon equivalent material are frequently welded without preheat. Thick sections, high restraint and high carbon equivalent require preheat and controlled interpass temperature, as defined by the qualified welding procedure and the governing fabrication standard.
Q: What is the difference between S355J2 and S355J2+N?
J2 is the toughness class with 27 J minimum Charpy energy at -20 °C. The +N suffix states that the steel is delivered in the normalized condition, which refines grain size and improves toughness consistency after hot forming.
Q: Is S355 equivalent to ASTM A572 Grade 50?
They are close in strength class, but A572 Grade 50 specifies a 345 MPa minimum yield for its usual thickness range, so S355 is slightly stronger on paper. Chemistry, toughness class and dimensional tolerances must all be checked before treating the two as interchangeable.
Q: Which S355 sub-grade should be used at -40 °C?
S355K2 guarantees 40 J of Charpy energy at -40 °C and is the direct choice. Where a lower carbon equivalent is needed for heavy welding, a thermo-mechanically rolled grade with matching low-temperature toughness can be specified instead.




