What ABS Grade E Plate Is Within the ABS Rules
ABS Grade E is a normal-strength hull structural steel approved under the American Bureau of Shipping Rules for Materials and Welding, Part 2, Chapter 1. It sits in the same family as Grades A, B and D. All four grades share a minimum yield strength of 235 MPa and a tensile range of 400-520 MPa, and they are separated only by the temperature at which the Charpy V-notch impact test is carried out: 0 °C for Grades A and B, -20 °C for Grade D and -40 °C for Grade E. That single number decides where the grade may be used, because a hull, an ice-class bow region or an offshore module exposed to Arctic air and seawater has to stay ductile far below freezing.
Guaranteed Chemistry and Property Envelope
Grade E plate is supplied fully killed and fine grained. Carbon is normally held to 0.18 % maximum, manganese to a minimum of 2.5 times carbon, silicon to 0.50 % maximum, phosphorus and sulphur to 0.035 % maximum and nitrogen to 0.02 % maximum, with aluminium, niobium, vanadium or titanium additions used for grain refinement in line with the IACS unified requirements for hull structural steel. Residual elements are controlled as carefully as the principal analysis, because copper, chromium and nickel residuals feed straight into the carbon equivalent value that governs welding behaviour.
| Property | Requirement for ABS Grade E |
|---|---|
| Minimum yield strength | 235 MPa |
| Tensile strength range | 400-520 MPa |
| Minimum elongation | 18 % |
| Impact test temperature | -40 °C |
| Charpy V-notch energy | 27 J minimum average transverse, 41 J longitudinal |
| Delivery condition | As-rolled, TMCP or normalized |
| Normal supply thickness | 6 mm to 100 mm |
Why the -40 °C Impact Requirement Drives Processing Choice
The low-temperature requirement is met through microstructure rather than through alloy loading. Plates are produced either by thermomechanical controlled processing, which refines the ferrite grain size and pushes the ductile-to-brittle transition temperature downwards, or by normalizing, which is often preferred for heavier sections and for orders that need a stable, stress-relieved delivery condition. Both routes have to demonstrate the same -40 °C absorbed energy on a heat-by-heat sampling basis. Grain refinement also protects the heat-affected zone: a fine starting microstructure limits the width of the coarse-grained region beside the fusion line, which is where brittle fracture usually starts in a welded hull.
Weldability, Carbon Equivalent and Crack Control
Grade E is bought as much for fabrication behaviour as for toughness. Mill chemistry is balanced so that the carbon equivalent value, CEV = C + Mn/6 + Cr/5 + Mo/5 + V/5 + Ni/15 + Cu/15, stays at or below about 0.40 % on plate rolled heavier than 50 mm, while the crack sensitivity index Pcm = C + Si/30 + Mn/20 + Cu/20 + Ni/60 + Cr/20 + Mo/15 + V/10 + 5B is kept low enough that thin and medium plate can be welded without preheating. In thick sections the practical controls are preheat matched to section size, hydrogen-controlled consumables and an interpass temperature limit, all fixed in the welding procedure qualification rather than assumed on site. Consumables are matched to the 400-520 MPa tensile band, and multi-pass procedures on plate above 50 mm are normally qualified with impact testing of both weld metal and heat-affected zone at -40 °C.
How a Supply Order Is Normally Defined
A typical purchase position for ABS Grade E covers thickness from 6 mm to 100 mm, widths to about 4050 mm and lengths to 15000 mm, with delivery condition, impact testing frequency and marking method stated on the order. Documentation usually means a mill test certificate carrying heat number traceability, chemical analysis, tensile results and impact energy, together with the classification society stamp reference when the plate is intended for a classed vessel. Optional testing includes ultrasonic examination, thickness-direction testing to Z15, Z25 or Z35 for welds loaded through the plate thickness, and independent third-party inspection at the works. Processing before shipment can cover flame or plasma cutting to drawing, edge beveling, drilling and shot blasting, which removes a handling step at the yard.
Frequently Asked Questions
Q: Is ABS Grade E stronger than ABS Grade A?
A: No. Both grades specify 235 MPa minimum yield strength and 400-520 MPa tensile strength. Grade E is chosen for its -40 °C impact test temperature, which is 40 °C colder than the Grade A test temperature.
Q: What Charpy value does ABS Grade E have to meet?
A: The requirement is a minimum average absorbed energy of 27 J in transverse testing at -40 °C, with 41 J applied to longitudinal specimens. Sampling frequency follows the classification society rules for the grade.
Q: Can ABS Grade E be supplied normalized?
A: Yes. Both normalized and TMCP deliveries are routine, and normalizing is usually chosen for heavy plate where consistent through-thickness properties and stress relief matter.
Q: Which through-thickness options are available?
A: Plate can be ordered with Z15, Z25 or Z35 thickness-direction testing where welded joints transfer load perpendicular to the plate surface.
Q: How is the material verified before shipment?
A: Each heat is covered by a mill test certificate showing chemical analysis, tensile results and impact energy at -40 °C, and ultrasonic examination or third-party inspection can be added to the order.
Q: Is preheat always needed when welding ABS Grade E?
A: Thin and medium plate with controlled carbon equivalent is normally welded without preheat, while thick sections and high-restraint joints are welded with preheat and hydrogen-controlled consumables under a qualified procedure.


