Wear Resistant Chromium Carbide Overlay Plate: Grades and Sizes

Nov 26, 2025 Leave a message

What Chromium Carbide Overlay Plate Is

Chromium carbide overlay plate, widely abbreviated as CCO plate, is a bimetallic wear product built from two very different layers. A tough mild steel base plate carries the structural load and provides the weldable interface, while a high-chromium, high-carbon alloy is deposited on the working face to resist abrasion. The overlay is applied by automatic open arc welding, and also by submerged arc welding for particular formats, creating a metallurgical fusion bond rather than a mechanical or adhesive joint. Because the two layers are fused, the hard facing does not separate, spall or corrode away from the backing plate, and the assembly tolerates elevated temperature far better than polymer linings.

Construction: Base Plate, Overlay and Bond

Base plate - mild steel such as A36, Q235B or Q345B, chosen for toughness, weldability and the ability to be rolled, drilled and bolted.

Overlay layer - a chromium carbide deposit containing up to 35% chromium and up to 5.5% carbon, giving extreme hardness and high abrasion resistance.

Bond - produced by open arc or submerged arc welding, a genuine metallurgical fusion that resists heat and prevents delamination.

The division of labour between the layers is the whole point of the product. The backing plate absorbs impact and structural stress and is easy to weld into a chassis, chute or hopper, while the deposit handles the sliding and gouging abrasion that would destroy a plain carbon steel surface within weeks.

Overlay Chemistry and Hardness

Overlay type C % Cr % Si % Mn % Hardness
Standard abrasion, moderate impact 4.8-5.5 23-28 0.7-1.5 0.6-1.0 60 HRC min
Severe abrasion, moderate impact 5.0-6.0 25-32 0.7-1.5 0.6-1.0 60 HRC min
High-chromium, maximum wear resistance 5.0-6.0 35-40 0.7-1.2 0.5-1.0 60 HRC min
Complex-carbide, hot and high-stress duty 5.0-6.2 20-25 0.7-1.2 0.4-0.8 60 HRC min, with Nb, V, Ti, Mo and W additions of about 5.0-6.5%

Across the range the deposit is measured at 58 to 65 HRC, with most production plate reaching 60 HRC or above. The complex-carbide variant trades some chromium for strong carbide formers such as niobium, vanadium, titanium, molybdenum and tungsten, which improves performance where the wear surface also runs hot, as in sinter plant and cement kiln applications.

Microstructure and Wear Performance

The hard phase in the deposit is chromium carbide, principally of the M7C3 form, and the volume fraction of primary carbide in the microstructure is above 50%. These carbides are distributed evenly through the overlay and grow in a fibrous, vertically oriented pattern on the wear face, which anchors them against being torn out under load. The practical consequence is abrasion resistance far beyond what a heat-treated carbon steel can offer. Comparative wear testing of overlay plate against reference materials reports roughly 20 to 30 times the resistance of mild steel and 8 to 12 times that of heat-treated steel, with the spread reflecting differences in test method and impact intensity. Values at the lower end of that band come from high-impact tests where chipping, not pure sliding abrasion, dominates the result.

Standard Sizes and Thickness Combinations

Component Range
Base plate thickness 3 mm to 100 mm
Overlay thickness 3 mm to 50 mm
Common combinations (base + overlay) 3+3, 4+4, 5+5, 6+4, 6+5, 6+6, 6+8, 8+4 to 8+8, 10+4 to 10+20, 12+4 to 12+12, 14+6 to 14+10, 16+6 to 16+10, 18+6 to 18+10, 20+5 to 20+20, 30+10, 40+10
Standard plate sizes 1400 x 3400 mm, 1400 x 3500 mm, 2100 x 3500 mm, 1480 x 3041 mm, 1470 x 3062 mm, 1460 x 3083 mm, 1000 x 1500 mm
Tolerances Flatness better than ±3 mm/m; overlay thickness tolerance 0 to 0.5 mm on open arc plate and 0 to 0.3 mm where tighter control is specified

Thinner combinations such as 3+3 are supplied in the smaller 1000 x 1500 mm format with about 1.5 square metres per sheet, while the heavier 4+4 to 12+12 combinations are typically rolled to about 1480 x 3041 mm or comparable sizes giving roughly 4.5 square metres per sheet. Other widths, lengths and thickness pairings, including 1400 x 2900 mm, 1500 x 3000 mm, 2000 x 3000 mm and 2100 x 3100 mm, are produced to order.

Fabrication: Cutting, Forming, Drilling and Fixing

Overlay plate can be cut, formed and assembled with the same shop equipment used for ordinary plate, and neither welding nor thermal cutting degrades the wear properties of the deposit. Drilling and countersinking are carried out from the base plate side, and pre-processed bolts can be embedded in the back of a liner so that worn plates can be changed quickly in the field. Cold forming into cones, chutes and curved liners is common, and matching welding wire is available for protecting internal joints and seams where the overlay has been cut back.

Typical Applications

Mining and quarrying: grizzly screens, skip liners, crusher liners, screen decks, truck bed liners.

Cement and thermal power: chute liners, hopper liners, fan blade liners, feed nozzles, coal yard equipment.

Metallurgy and steelmaking: breaker liners and bars, skirt plates, feeder trays, bucket liners.

Construction machinery and bulk handling: loader buckets, transfer points, hoppers and discharge chutes.

In each case the return on the material comes from extended service life, which reduces the frequency of shutdowns, the labour cost of relining and the production lost while equipment is stopped.

Checks Before Placing an Order

Confirm the abrasion and impact balance of the duty; a maximum-chromium grade is not automatically the best choice where heavy impact is present.

State the base and overlay thicknesses separately, never a single total, so that the backing thickness needed for welding and bolting is preserved.

Ask for the hardness range and the carbide volume fraction on the test certificate, not just the headline HRC figure.

Confirm flatness and thickness tolerance, especially for liners that must seat against a flat frame.

Agree the fixing method, whether drilled holes, countersunk holes, embedded bolts or plain weld-on plate.

Frequently Asked Questions

Q: What does CCO stand for?
Chromium carbide overlay. The name describes both the alloy system and the deposition process used to bond it to the base plate.

Q: Can overlay plate be welded without losing its wear resistance?
Yes. Welding and cutting do not affect the properties of the overlay, though the cut edge should be protected with matching wire where slurry or fines will flow across it.

Q: How hard is chromium carbide overlay plate?
Typically 58 to 65 HRC, with most plate at 60 HRC or above; deposits thicker than about 12 mm commonly exceed 62 HRC.

Q: What is the difference between the standard and complex-carbide overlays?
The standard grades rely on chromium carbide with 23 to 40% chromium, while complex-carbide grades add niobium, vanadium and similar elements for hot or high-stress duty.

Q: Is overlay plate suitable for impact applications?
It is designed for high abrasion with low to moderate impact. Where shock loading dominates, a thicker base plate and a tougher overlay chemistry should be selected.

Q: Can it be formed into curved liners?
Yes. The plate can be cold formed into cones and curved profiles and can be bent, drilled and assembled like conventional steel plate.