EN 10025-6 S890QL Plate: Specification and Stock Ranges

Dec 31, 2025 Leave a message

What S890QL Plate Is

S890QL is a flat rolled, high yield strength structural steel supplied in the quenched and tempered condition under EN 10025-6. The grade code reads directly: S for structural steel, 890 for the minimum yield strength in MPa, Q for the quench and temper route, and L for the impact quality tested at -40 °C. The stronger L1 quality is tested at -60 °C for colder service.

The combination of near-900 MPa yield strength with a -40 °C toughness requirement places the grade at the demanding end of commercial plate production. It is bought by manufacturers of cranes, mining and earth-moving equipment, heavy transport vehicles, hydraulic attachment arms and offshore lifting appliances, where a small reduction in plate thickness translates into a large reduction in the mass that the machine has to lift and carry.

Specified Properties

Property Thickness 3-50 mm Thickness >50-100 mm
Minimum yield strength ReH 890 MPa 830 MPa
Tensile strength Rm 940-1100 MPa 880-1100 MPa
Minimum elongation 11% 11%
Charpy V-notch, minimum 30 J at -40 °C 30 J at -40 °C
Delivery condition Quenched and tempered Quenched and tempered

The chemistry window is similar to the rest of the high-strength quenched and tempered family, with carbon capped around 0.20%, manganese up to 1.70%, and nickel, chromium and molybdenum used to develop hardenability and toughness. Sulphur and phosphorus are held at low levels to protect through-thickness ductility and heat-affected zone toughness. Carbon equivalent is calculated in accordance with the standard and reported per heat.

Typical Supply Range

Typical industry stock and production ranges for S890QL plate are thickness 8-80 mm, width 1500-3200 mm and length up to 12000 mm, with the full 890 MPa guarantee in the lighter half of that band and the 830 MPa level applying above 50 mm. Cut-to-length plate, plasma-cut profiles, waterjet-cut blanks, sawn blocks and machined pads are all supplied against drawing, which removes the thermal cutting operation and its hardened edge from the customer's shop floor.

Because the grade is normally consumed in components with tight tolerances, flatness and thickness tolerance deserve as much attention as the mechanical properties. Plate is supplied to the dimensional tolerances of EN 10029, with tighter flatness classes available on request, and edge condition is controlled so that sheared or flame-cut edges do not introduce crack initiation sites in fatigue-loaded parts.

Testing, Certification and Traceability

Every consignment is issued with an inspection certificate to EN 10204 in the 3.1 form, covering heat analysis, product analysis, tensile testing, Charpy testing at -40 °C and dimensional inspection; 3.2 certification with an independent witness is available where the design authority requires it. Ultrasonic examination to EN 10160 at an agreed class is routinely ordered for plate above roughly 20 mm, and hardness verification across the plate surface is a practical confirmation that the quenched and tempered condition has been delivered.

Traceability is maintained from the steel heat through each processing step. Plate marking carries the grade, heat number, thickness and, where applicable, the customer's part reference, and can be transferred to cut parts on request so that a finished component can be linked back to its mill certificate. Thickness-direction testing to EN 10164 in Z25 and Z35 classes is available for joints loaded through the plate thickness.

Fabrication Notes for the Buyer

An 890 MPa steel is not welded like ordinary structural plate. A qualified welding procedure with a defined preheat, a maximum heat input, an interpass temperature ceiling and low-hydrogen consumables matched to the strength class is essential, and the procedure qualification should include a heat-affected zone hardness traverse. Software-controlled welding sets that record heat input help keep production within the qualified envelope.

Cold forming is possible but requires generous radii and clean, burr-free edges; any hot forming above the tempering temperature destroys the delivered condition and requires re-quenching and tempering. Drilling and machining are straightforward with carbide tooling at moderate speeds. Where parts are thermally cut on site, the hardened layer on the cut face is removed by grinding before the part enters fatigue service or is welded.

Ordering information that avoids delays and disputes includes the ordered thickness and tolerance class, the required impact quality, the standard of ultrasonic examination, the certificate form, the dimensional tolerance class, the edge condition and, for cut parts, the drawing revision and the nesting arrangement. Buyers who also need the plate in lighter strength classes can consolidate a mixed order across S690QL, S690Q and S890QL to reduce freight and handling costs.

Frequently Asked Questions

Q: What does the L in S890QL mean?

A: It identifies the impact quality, with Charpy V-notch testing at -40 °C and a minimum absorbed energy of 30 J.

Q: What is the minimum yield strength of S890QL plate?

A: 890 MPa from 3 mm to 50 mm thickness, reducing to 830 MPa between 50 mm and 100 mm.

Q: What thickness can be ordered?

A: Typical production covers 8-80 mm, with the strongest mechanical guarantee in the 8-50 mm band.

Q: Is ultrasonic examination included as standard?

A: It is a supplementary requirement rather than a base one. It can be ordered to EN 10160 at the class appropriate to the application.

Q: Which certificate forms are issued?

A: Inspection certificates to EN 10204 3.1 are standard, and 3.2 certification with independent witnessing is available.

Q: Can S890QL plate be bent cold?

A: Yes, within defined minimum bend radii and with clean edges. The lower elongation of 11% means the forming envelope is tighter than for a 690 MPa grade.