Two Toughness Classes from the Same EN 10025-2 Family
S355JR and S355J0 are hot-rolled structural steel plate grades defined by EN 10025-2, the European standard for non-alloy structural steels. Both carry a minimum yield strength (ReH) of 355 MPa and share the same tensile window of 450-680 MPa for plate between 3 mm and 16 mm thick, so the two grades are frequently treated as interchangeable. They are not. The grades differ in specified chemistry and, more importantly, in the minimum Charpy V-notch impact energy temperature, which decides whether a structure can be certified for a given service condition.
How to Read the Grade Designation
S - structural steel.
355 - minimum yield strength in MPa, referenced to thicknesses up to 16 mm.
JR - 27 J minimum Charpy V-notch energy at +20 °C.
J0 - 27 J minimum Charpy V-notch energy at 0 °C.
J2 - 27 J minimum Charpy V-notch energy at -20 °C.
K2 - 40 J minimum Charpy V-notch energy at -20 °C.
Because the impact test is performed on a notched specimen held at a fixed low temperature, a plate that comfortably satisfies JR can still fail at 0 °C. That is the practical core of the JR versus J0 decision, and it is the reason the two grades cannot be swapped on a drawing without checking the design temperature.
Chemical Composition Comparison
| Element, max % | S355JR | S355J0 |
|---|---|---|
| C | 0.27 | 0.24 |
| Si | 0.60 | 0.60 |
| Mn | 1.70 | 1.70 |
| P | 0.045 | 0.040 |
| S | 0.045 | 0.040 |
| Cu | 0.60 | 0.60 |
| N | 0.014 | 0.014 |
The tighter carbon, phosphorus and sulphur limits are what separate the two products at the mill. Lower residuals reduce segregation and lift the upper-shelf toughness of the plate, giving J0 material enough margin to hold 27 J at 0 °C rather than at room temperature. Silicon, manganese, copper and nitrogen limits are identical, so weldability expressed as carbon equivalent (CEV) is broadly comparable and existing welding procedures can usually be re-qualified with a thickness and consumable review rather than a full re-write.
Mechanical Properties and Impact Testing
| Property | S355JR | S355J0 |
|---|---|---|
| Yield strength ReH, min (t not more than 16 mm) | 355 MPa | 355 MPa |
| Tensile strength Rm (3 mm to 16 mm) | 450-680 MPa | 450-680 MPa |
| Elongation A, min (3 mm to 40 mm) | 22% | 22% |
| Charpy V-notch test temperature | +20 °C | 0 °C |
| Impact energy, longitudinal, min | 27 J | 27 J |
Yield strength falls as plate thickness rises, so the 355 MPa figure applies to the reference range and a lower guaranteed value governs heavier sections. Charpy testing is normally carried out on longitudinal specimens; transverse values are appreciably lower and must be agreed in writing if the design relies on them. Certificates report a three-specimen average together with a single minimum value, which means a 27 J specification does not guarantee 27 J on every test bar.
Applications and Selection Guidance
S355JR - general fabrication, storage tanks, industrial flooring, machine bases, support frames and indoor structures where the service temperature stays comfortably above freezing.
S355J0 - outdoor structures, cold-climate buildings, bridges and crane components, transport frames, and equipment that sees winter conditions or refrigerated environments.
Choose J0 rather than JR whenever the steel may see 0 °C or lower in service, or whenever the client specification, national annex or notified body demands a validated impact class. For service below 0 °C, S355J2 is the usual next step, because it repeats the 27 J requirement at -20 °C, and S355K2 is specified when a 40 J energy level is required at the same temperature.
Fabrication and Delivery Condition Notes
S355JR is generally supplied as-rolled, while S355J0 is often delivered normalized or normalized-rolled in order to secure the impact result repeatably. Both grades weld with low-hydrogen consumables matched to the parent metal strength, and heat input control matters more to toughness than the grade difference itself. Cold forming is routine for the JR grade; bending radii should be increased as thickness grows or when the delivery condition is normalized, and any cold-worked zone that will operate at low temperature should be stress-relieved or re-tested.
Frequently Asked Questions
Q: Are S355JR and S355J0 the same steel with different certificates?
No. They have different specified chemical limits and different impact test temperatures, so J0 plate is a genuinely tougher product rather than a paperwork variant.
Q: What is the single most important difference?
The Charpy V-notch test temperature: +20 °C for JR against 0 °C for J0, at the same 27 J energy level.
Q: Can S355JR be substituted for S355J0?
Only if the design temperature is safely above freezing and the client or code accepts the substitution in writing; otherwise the certificate will not match the specification.
Q: Which grade welds more easily?
Weldability is similar because the carbon equivalent ranges overlap. The J0 grade carries lower carbon and sulphur, which slightly reduces cracking risk in restrained joints.
Q: How is the Charpy test carried out?
Three notched bars are cooled to the specified temperature and struck in one blow; the absorbed energy is reported as a three-specimen average plus the lowest single value.
Q: What should be specified for -20 °C service?
S355J2 for 27 J, or S355K2 where 40 J is required; neither JR nor J0 covers that temperature.





