SS490 Steel Plate: JIS G3101 High-Strength Structural Grade Explained

Oct 14, 2025 Leave a message

What Is SS490 Steel Plate?

SS490 is a hot-rolled structural steel plate grade specified in JIS G3101, the Japanese Industrial Standard for rolled steels for general structure. The designation follows the JIS naming rule: the letters SS identify structural steel, and the number 490 is the minimum tensile strength in N/mm2 (MPa). SS490 delivers a minimum yield strength of 275 MPa together with a tensile strength range of 490-610 MPa, placing it one strength class above SS400 while keeping the same general-purpose character.

JIS G3101 is a general structural standard rather than a welded-structure standard. It fixes chemical composition and tensile properties, but it does not impose a guaranteed impact energy or a weldability guarantee. Where a project specification calls for guaranteed Charpy energy or a normalized delivery condition, the JIS G3106 SM490 series or an equivalent welded structural grade is normally selected instead.

SS490 Chemical Composition

JIS G3101 controls the chemical composition of SS490 by heat analysis, with limits that keep the plate formable, weldable under controlled procedures and predictable in service.

Element t ≤ 16 mm, max % t > 16 mm, max %
C 0.24 0.24
Si 0.55 0.55
Mn 1.60 1.60
P 0.045 0.045
S 0.045 0.045

Manganese at up to 1.60% provides solid-solution strengthening, while the 0.24% carbon ceiling and the 0.045% limits on phosphorus and sulphur keep segregation, hot-cracking risk and loss of notch ductility under control during cutting, bending and welding.

Mechanical Properties of SS490 Steel Plate

Property SS490 (JIS G3101) SS400 (JIS G3101) SM490 (JIS G3106)
Minimum yield strength, t ≤ 16 mm 275 MPa 245 MPa 325 MPa
Tensile strength 490-610 MPa 400-510 MPa 490-610 MPa
Delivery condition As-rolled As-rolled As-rolled or normalized
Impact energy guaranteed by standard No No Yes, by grade suffix
Weldability guarantee No No Yes

Yield values in JIS G3101 are quoted for a reference thickness range and decrease as plate thickness increases. Designers should therefore work from the yield value that applies to the actual section thickness rather than from the headline number, and should confirm the applicable value before reducing a section size.

SS490 vs SS400 vs SM490: Which Grade to Use

SS400 - the lowest strength of the three and the most widely available general structural grade; a sound choice for frames, supports and general fabrication where a 245 MPa minimum yield is sufficient.

SS490 - roughly 12% higher minimum yield than SS400 at the same tensile class; selected when load capacity has to rise without changing fabrication practice or moving to a fully weldable specification.

SM490 - the same tensile band as SS490, but issued under a welded-structure standard with guaranteed impact properties and weldability, and available in normalized or thermo-mechanically rolled conditions.

In practice the governing design code decides. If the code requires a guaranteed impact test or a weldable structural grade, SM490 applies; if the structure is general and the design is strength driven, SS490 is the more economical route.

Typical Applications of SS490 Steel Plate

General construction: bridges, factory buildings and workshops.

Construction machinery: excavators, bulldozers, cranes and drilling rigs.

Shipbuilding: hull components and internal structures.

Railway and other equipment: structural components working under static and moderate dynamic loading.

SS490 plate also serves as base material for flame-cut brackets, gusset plates, machine bases and support frames, where the additional strength over SS400 allows a lighter section without altering workshop practice.

Plates are normally supplied as-rolled with a mill finish and can be delivered with an EN 10204 type 3.1 or 3.2 inspection certificate. Where the project demands it, additional verification can be provided, including high-tension testing, low-temperature Charpy impact testing on a simulated post-weld heat treatment condition, ultrasonic examination, shot blasting and priming, and profile cutting or edge preparation to drawing. Plate and section thickness tolerance, flatness and edge condition are commonly agreed to the general requirements of ASTM A6/A6M for rolled structural products.

Frequently Asked Questions

Q: What does the number 490 in SS490 mean?
It is the minimum tensile strength expressed in N/mm2 (MPa). SS490 plate must reach at least 490 MPa tensile strength, with the specification range running from 490 to 610 MPa.

Q: Is SS490 the same as SM490?
No. SS490 is issued under JIS G3101 for general structure and carries no impact or weldability guarantee. SM490 is issued under JIS G3106 with guaranteed impact energy and weldability, and may be supplied normalized.

Q: What is the minimum yield strength of SS490 steel plate?
275 MPa for plate up to 16 mm thick. The required minimum falls as thickness increases, so the value for the actual plate thickness must be used in design.

Q: Is SS490 stronger than SS400?
Yes. Minimum yield strength is 275 MPa against 245 MPa for SS400, and minimum tensile strength is 490 MPa against 400 MPa, so a thinner SS490 section can carry a comparable load.

Q: Can SS490 steel plate be welded?
Yes, with qualified procedures and consumables matched to the base metal strength. Because the standard sets no weldability guarantee, preheat and interpass control should be specified for thicker sections and restrained joints.

Q: Is impact testing mandatory for SS490?
JIS G3101 does not mandate a Charpy impact test for SS490. Impact energy can nevertheless be verified at room or low temperature when a project specification or an application such as cold-climate structures requires it.