What SA285 Grade A Is
ASTM A285/A285M, adopted by ASME as SA-285/SA-285M, covers low and intermediate tensile strength carbon steel plates for pressure vessels. The specification contains three grades, A, B and C, and strength rises with the grade, so Grade A is the lowest and Grade C the highest. Grade A is not a low-temperature material and it is not intended for high-pressure duty: it exists for storage tanks, low-pressure vessels and other equipment where moderate strength and excellent fabrication behaviour are more valuable than a high design stress.
Chemistry to A285/A285M
| Element | SA285 Grade A limit |
|---|---|
| Carbon | 0.17 % maximum |
| Silicon | 0.08-0.45 % |
| Manganese | 0.98 % maximum |
| Phosphorus | 0.035 % maximum |
| Sulphur | 0.035 % maximum |
The carbon equivalent value, CEV = C + Mn/6 + Cr/5 + Mo/5 + V/5 + Ni/15 + Cu/15, is reported with the heat analysis because it predicts how the plate will behave when welded. The low carbon content and the capped manganese level are the reason Grade A accepts welding without preheating in normal thicknesses and can be cold formed into tank shells and heads with heavy reduction.
Mechanical Properties and Plate Range
| Thickness | Minimum yield strength | Tensile range | Minimum elongation |
|---|---|---|---|
| 6-50 mm | 165 MPa | 310-450 MPa | 30 % |
| 50-200 mm | 165 MPa | 310-450 MPa | 27 % |
The tensile range corresponds to roughly 45-65 ksi, which places the grade well below a structural steel of similar thickness and explains its wide elongation allowance. Plate is produced from 6 mm to 300 mm in thickness, 1500 mm to 4050 mm in width and 3000 mm to 15000 mm in length. Because the strength does not change with thickness across the normal range, the yield value is predictable for design purposes, and weight is saved by using a heavier section rather than by specifying a stronger grade.
Equivalent Grades Elsewhere
The European equivalent is EN 10028-2 P235GH, the elevated-temperature pressure vessel plate grade, and the Japanese equivalent is JIS G3115 SPV 24. British standards list 161 Grade 360 and 164 Grade 360 in the same role, German practice uses HI, Spanish practice uses A 37 RCI and Italian practice uses Fe 60-1KW. These equivalences are based on room-temperature tensile and yield levels; where a project calls for elevated-temperature design stress, the creep and high-temperature yield data of the specific specification must be compared before a substitution is accepted.
Supplementary Testing and Fabrication
Hydrogen-induced cracking testing and compliance with NACE MR0175 requirements can be specified where the vessel will handle wet sour service, and thickness-direction testing to Z15, Z25 or Z35 can be added where nozzle and support welds load the plate through its thickness. Supplementary requirements S57, S57.1, S58, S58.1, S3 and S4 of the A285 specification cover additional tensile, notch toughness and ultrasonic provisions that can be written into the order. In fabrication, Grade A is welded with carbon steel electrodes matched to the low strength level, formed cold with generous bend radii and, where heavy cold forming is followed by welding, given a stress-relief heat treatment. Storage tank shells, low-pressure vessel bodies and temperature-controlled tanks are the usual end products, and plate is commonly supplied cut to size with beveled longitudinal seams ready for the shell rolling line.
Frequently Asked Questions
Q: Is SA285 Grade A the same as ASTM A285 Grade A?
A: Yes. SA-285/SA-285M is the ASME designation of the same specification published by ASTM as A285/A285M, so the chemistry and mechanical requirements are identical.
Q: What is the tensile strength of SA285 Grade A?
A: The specified tensile range is 310-450 MPa, equivalent to about 45-65 ksi, with a minimum yield strength of 165 MPa throughout the normal thickness range.
Q: Which grades exist in the A285 family?
A: The specification covers Grades A, B and C with increasing strength. Grade A is the lowest strength grade and Grade C the highest.
Q: What is SA285 Grade A used for?
A: Storage tanks, low-pressure vessels, temperature-controlled tanks and similar equipment where weldability and formability matter more than a high design stress.
Q: Can SA285 Grade A be used at low temperature?
A: It is not a low-temperature steel. Service temperature, notch toughness requirements and any supplementary impact testing should be reviewed against the design code before the grade is selected for cold service.
Q: Which supplementary testing can be ordered?
A: Hydrogen-induced cracking testing, NACE MR0175 compliance, thickness-direction testing to Z15, Z25 or Z35 and the supplementary requirements S3, S4, S57, S57.1, S58 and S58.1 of the specification can all be added to the order.






