S890Q and S960Q are ultra-high-strength structural steels supplied in the quenched and tempered (Q&T) condition under EN 10025-6.
They are widely used in cranes, heavy engineering, mining equipment, offshore structures, and high-load steel constructions where weight reduction and structural efficiency are critical.
Although the two grades are closely related, they differ significantly in strength level, fabrication difficulty, welding sensitivity, cost, and application suitability.
| Item | S890Q | S960Q |
|---|---|---|
| Standard | EN 10025-6 | EN 10025-6 |
| Delivery condition | Quenched & Tempered | Quenched & Tempered |
| Grade level | Ultra-high-strength structural steel | Higher-strength UHSS |
| Design focus | High strength with good fabricability | Maximum strength & weight saving |
Key takeaway:
👉 S960Q offers higher strength than S890Q, but at the cost of increased fabrication complexity.
Chemical Composition Comparison
| Element | S890Q (max, %) | S960Q (max, %) |
|---|---|---|
| Carbon (C) | 0.22 | 0.20 |
| Silicon (Si) | 0.86 | 0.86 |
| Manganese (Mn) | 1.8 | 1.8 |
| Phosphorus (P) | 0.03 | 0.03 |
| Sulfur (S) | 0.017 | 0.017 |
| Chromium (Cr) | 1.6 | 1.6 |
| Molybdenum (Mo) | 0.74 | 0.74 |
| Nickel (Ni) | 2.1 | 2.1 |
| Boron (B) | 0.006 | 0.006 |
Properties
-
Mechanical Properties
| Property | S890Q | S960Q |
|---|---|---|
| Yield Strength (≥) | 890 MPa (≤50mm)830 MPa (50-100mm) | 960 MPa (≤50mm) |
| Elongation (≥) | 11% | 10% |
| Impact Energy | ≥30J at -20°C | ≥30J at -20°C |
| Fatigue Resistance | High | Very High |
| Weldability | Good (CEV ≤0.82) | Excellent (CEV ≤0.82) |
-
Cutting Performance
S890Q
Flame and plasma cutting are generally acceptable
Heat-affected zone (HAZ) hardness is controllable
S960Q
More pronounced HAZ hardening
Fine plasma or water-jet cutting is preferred
Edge grinding is often recommended after cutting

-
Cold Forming & Bending
| Item | S890Q | S960Q |
|---|---|---|
| Springback | High | Very high |
| Minimum bending radius | Smaller | Larger |
| Forming risk | Moderate | High |
-
Welding Distortion Control
S960Q generates higher residual stresses
Requires:
Optimized welding sequence
Rigid fixtures
Controlled heat input
This increases manufacturing time and cost compared to S890Q.
Applications

Overlapping Applications:
Heavy Machinery: Mining equipment (drill rigs, excavators, loaders)
Construction Cranes: Boom arms, chassis components
Transport Vehicles: Heavy-duty trucks, concrete pumpers, armored vehicles
Bridges: Main towers and steel girders in suspension/cable-stayed bridges
Offshore Structures: Wind turbine supports, drilling platforms
-
S960Q Preferred For:
Structures requiring maximum strength with minimal weight (e.g., aerospace components)
Ultra-heavy mining trucks (100+ ton capacity)
High-rise building cores and mega-columns
Military equipment requiring ballistic protection
-
S890Q Preferred For:
General industrial machinery where 890MPa strength is sufficient
Applications balancing cost and performance
Components requiring slightly better formability
Key Differences Summary
Strength Gap: S960Q offers 70 MPa higher yield strength (960 vs 890 MPa), enabling ~8% higher load capacity or 8% weight reduction
Cost Factor: S960Q typically costs 10-15% more than S890Q due to more stringent production requirements
Design Implications:
- S960Q allows for smaller cross-sections, reducing material usage
- S890Q provides better balance between strength and workability in some applications
Material Selection Guide:
- Choose S960Q when: Ultimate strength, light weight, and premium performance are critical
- Choose S890Q when: The 890MPa strength level is adequate, and cost efficiency matters

How to Choose Between S890Q and S960Q
Choose S890Q if:
You need high strength with reliable weldability
Your structure involves bending, welding, or complex geometry
You want balanced performance and cost
Choose S960Q if:
Weight reduction is the primary design driver
Your fabrication team has UHSS experience
Welding and forming processes are tightly controlled
GNEE Steel – Your Reliable UHSS Supplier
GNEE Steel supplies S690Q, S890Q, S960Q, S890QL, and S960QL in accordance with EN 10025-6, with strengths including:
- Stable Q&T heat treatment
- Strict thickness & flatness control
- Consistent mechanical properties
- Export experience for cranes, mining, and heavy structures
- Technical support for welding, cutting, and forming
📩 If you are evaluating S890Q vs S960Q for your project, contact GNEE Steel for technical guidance and competitive pricing.
Q1: What is S890Q steel plate?
A:S890Q is a high-strength structural steel plate according to EN 10025-6, supplied in quenched and tempered (Q) condition, with a minimum yield strength of 890 MPa.
Q2: What is the material number of S890Q?
A:The European material number for S890Q is 1.8940.
Q3: Is S890Q considered non-alloy steel?
A:Yes. Under EN classification, S890Q is listed as non-alloy structural steel, although small alloying elements are added for strength and toughness control.
Q4: What thickness range is available for S890Q steel plate?
A:Common supply thickness ranges from 6 mm to 150 mm, depending on mill capability and standard requirements.
Q5: What are the mechanical properties of S890Q?
A:
Yield strength: ≥ 890 MPa (≤ 50 mm)
Tensile strength: 940–1100 MPa
Elongation: ≥ 11%
Impact test: ≥ 30 J at −20°C
Q6: Can S890Q steel be welded easily?
A:Yes, S890Q has good weldability, but welding must follow controlled procedures, including proper heat input, preheating (if required), and suitable filler materials.
Q7: What is the difference between S890Q and S890QL?
A:S890QL offers better low-temperature impact toughness than S890Q and is typically specified for colder environments or critical structures.
Q8: What are typical applications of S890Q steel plate?
A:S890Q is widely used in:
Cranes and lifting equipment
Bridges and heavy structures
Mining and earthmoving machinery
Wind power and offshore structures
Heavy-duty vehicle frames
Q9: Can S890Q replace S690Q to reduce weight?
A:Yes. Using S890Q instead of S690Q allows significant weight reduction while maintaining or increasing load capacity, which is especially valuable for mobile equipment.
Q10: What inspection and certificates are required for S890Q?
A:Standard supply includes EN 10204 3.1 MTC.
3.2 certificates, ultrasonic testing (UT), and third-party inspection (SGS, BV, TUV) are available upon request.
Q11: Is S890Q suitable for pressure vessel applications?
A:No. S890Q is a structural steel, not designed for pressure vessel or boiler applications. Pressure vessel steels must comply with specific PV standards such as EN 10028 or ASME.
Q12: What delivery condition is required for S890Q steel plate?
A:S890Q must be supplied in quenched and tempered (Q) condition as per EN 10025-6.
Q13: Can you cut or machine S890Q steel plate?
A:Yes. Flame cutting, plasma cutting, and machining are possible with controlled parameters to maintain material properties.
Q14: Does S890Q steel require special storage or handling?
A:Standard dry storage is sufficient. Surface protection can be added for long-term outdoor storage.
| Grades Of Carbon and Low-alloy High-strength Steels Supplied By GNEE | |||||
| ASTM/ASME | ASTM A36/A36M | ASTM A36 | |||
| ASTM A283/A283M | ASTM A283 Grade A | ASTM A283 Grade B | ASTM A283 Grade C | ASTM A283 Grade D | |
| ASTM A514/A514M | ASTM A514 Grade A | ASTM A514 Grade B | ASTM A514 Grade C | ASTM A514 Grade E | |
| ASTM A514 Grade F | ASTM A514 Grade H | ASTM A514 Grade J | ASTM A514 Grade K | ||
| ASTM A514 Grade M | ASTM A514 Grade P | ASTM A514 Grade Q | ASTM A514 Grade R | ||
| ASTM A514 Grade S | ASTM A514 Grade T | ||||
| ASTM A572/A572M | ASTM A572 Grade 42 | ASTM A572 Grade 50 | ASTM A572 Grade 55 | ASTM A572 Grade 60 | |
| ASTM A572 Grade 65 | |||||
| ASTM A573/A573M | ASTM A573 Grade 58 | ASTM A573 Grade 65 | ASTM A573 Grade 70 | ||
| ASTM A588/A588M | ASTM A588 Grade A | ASTM A588 Grade B | ASTM A588 Grade C | ASTM A588 Grade K | |
| ASTM A633/A633M | ASTM A633 Grade A | ASTM A633 Grade C | ASTM A633 Grade D | ASTM A633 Grade E | |
| ASTM A656/A656M | ASTM A656 Grade 50 | ASTM A656 Grade 60 | ASTM A656 Grade 70 | ASTM A656 Grade 80 | |
| ASTM A709/A709M | ASTM A709 Grade 36 | ASTM A709 Grade 50 | ASTM A709 Grade 50S | ASTM A709 Grade 50W | |
| ASTM A709 Grade HPS 50W | ASTM A709 Grade HPS 70W | ASTM A709 Grade 100 | ASTM A709 Grade 100W | ||
| ASTM A709 Grade HPS 100W | |||||
| ASME SA36/SA36M | ASME SA36 | ||||
| ASME SA283/SA283M | ASME SA283 Grade A | ASME SA283 Grade B | ASME SA283 Grade C | ASME SA283 Grade D | |
| ASME SA514/SA514M | ASME SA514 Grade A | ASME SA514 Grade B | ASME SA514 Grade C | ASME SA514 Grade E | |
| ASME SA514 Grade F | ASME SA514 Grade H | ASME SA514 Grade J | ASME SA514 Grade K | ||
| ASME SA514 Grade M | ASME SA514 Grade P | ASME SA514 Grade Q | ASME SA514 Grade R | ||
| ASME SA514 Grade S | ASME SA514 Grade T | ||||
| ASME SA572/SA572M | ASME SA572 Grade 42 | ASME SA572 Grade 50 | ASME SA572 Grade 55 | ASME SA572 Grade 60 | |
| ASME SA572 Grade 65 | |||||
| ASME SA573/SA573M | ASME SA573 Grade 58 | ASME SA573 Grade 65 | ASME SA573 Grade 70 | ||
| ASME SA588/SA588M | ASME SA588 Grade A | ASME SA588 Grade B | ASME SA588 Grade C | ASME SA588 Grade K | |
| ASME SA633/SA633M | ASME SA633 Grade A | ASME SA633 Grade C | ASME SA633 Grade D | ASME SA633 Grade E | |
| ASME SA656/SA656M | ASME SA656 Grade 50 | ASME SA656 Grade 60 | ASME SA656 Grade 70 | ASME SA656 Grade 80 | |
| ASME SA709/SA709M | ASME SA709 Grade 36 | ASME SA709 Grade 50 | ASME SA709 Grade 50S | ASME SA709 Grade 50W | |
| ASME SA709 Grade HPS 50W | ASME SA709 Grade HPS 70W | ASME SA709 Grade 100 | ASME SA709 Grade 100W | ||
| ASME SA709 Grade HPS 100W | |||||
| EN10025 | EN10025-2 | EN10025-2 S235J0 | EN10025-2 S275J0 | EN10025-2 S355J0 | EN10025-2 S355K2 |
| EN10025-2 S235JR | EN10025-2 S275JR | EN10025-2 S355JR | EN10025-2 S420J0 | ||
| EN10025-2 S235J2 | EN10025-2 S275J2 | EN10025-2 S355J2 | |||
| EN10025-3 | EN10025-3 S275N | EN10025-3 S355N | EN10025-3 S420N | EN10025-3 S460N | |
| EN10025-3 S275NL | EN10025-3 S355NL | EN10025-3 S420NL | EN10025-3 S460NL | ||
| EN10025-4 | EN10025-4 S275M | EN10025-4 S355M | EN10025-4 S420M | EN10025-4 S460M | |
| EN10025-4 S275ML | EN10025-4 S355ML | EN10025-4 S420ML | EN10025-4 S460ML | ||
| EN10025-6 | EN10025-6 S460Q | EN10025-6 S460QL | EN10025-6 S460QL1 | EN10025-6 S500Q | |
| EN10025-6 S500QL | EN10025-6 S500QL1 | EN10025-6 S550Q | EN10025-6 S550QL | ||
| EN10025-6 S550QL1 | EN10025-6 S620Q | EN10025-6 S620QL | EN10025-6 S620QL1 | ||
| EN10025-6 S690Q | EN10025-6 S690QL | EN10025-6 S690Q1 | EN10025-6 S890Q | ||
| EN10025-6 S890QL | EN10025-6 S890QL1 | EN10025-6 S960Q | EN10025-6 S960QL | ||
| EN 10149 | EN 10149-2 | S315MC | S355MC | S420MC | S460MC |
| S500MC | S550MC | S600MC | S650MC | ||
| S700MC | S900MC | S960MC | |||
| JIS | JIS G3101 | JIS G3101 SS330 | JIS G3101 SS400 | JIS G3101 SS490 | JIS G3101 SS540 |
| JIS G3106 | JIS G3106 SM400A | JIS G3106 SM400B | JIS G3106 SM400C | JIS G3106 SM490A | |
| JIS G3106 SM490YA | JIS G3106 SM490B | JIS G3106 SM490YB | JIS G3106 SM490C | ||
| JIS G3106 SM520B | JIS G3106 SM520C | JIS G3106 SM570 | |||
| DIN | DIN 17100 | DIN17100 St52-3 | DIN17100 St37-2 | DIN17100 St37-3 | DIN17100 RSt37-2 |
| DIN17100 USt37-2 | |||||
| DIN 17102 | DIN17102 StE315 | DIN17102 EStE315 | DIN17102 TStE315 | DIN17102 WStE315 | |
| DIN17102 StE355 | DIN17102 EStE355 | DIN17102 TStE355 | DIN17102 WStE355 | ||
| DIN17102 StE380 | DIN17102 EStE380 | DIN17102 TStE380 | DIN17102 WStE380 | ||
| DIN17102 StE420 | DIN17102 EStE420 | DIN17102 TStE420 | DIN17102 WStE420 | ||
| DIN17102 StE460 | DIN17102 EStE460 | DIN17102 TStE460 | DIN17102 WStE460 | ||
| DIN17102 StE500 | DIN17102 EStE500 | DIN17102 TStE500 | DIN17102 WStE500 | ||
| DIN17102 EStE285 | |||||
| GB | GB/T700 | GB/T700 Q235A | GB/T700 Q235B | GB/T700 Q235C | GB/T700 Q235D |
| GB/T700 Q275 | |||||
| GB/T1591 | GB/T1591 Q345A | GB/T1591 Q390A | GB/T1591 Q420A | GB/T1591 Q420E | |
| GB/T1591 Q345B | GB/T1591 Q390B | GB/T1591 Q420B | GB/T1591 Q460C | ||
| GB/T1591 Q345C | GB/T1591 Q390C | GB/T1591 Q420C | GB/T1591 Q460D | ||
| GB/T1591 Q345D | GB/T1591 Q390D | GB/T1591 Q420D | GB/T1591 Q460E | ||
| GB/T1591 Q345E | GB/T1591 Q390E | ||||
| GB/T16270 | GB/T16270 Q550C | GB/T16270 Q550D | GB/T16270 Q550E | GB/T16270 Q550F | |
| GB/T16270 Q620C | GB/T16270 Q620D | GB/T16270 Q620E | GB/T16270 Q620F | ||
| GB/T16270 Q690C | GB/T16270 Q690D | GB/T16270 Q690E | GB/T16270 Q690F | ||
| GB/T16270 Q800C | GB/T16270 Q800D | GB/T16270 Q800E | GB/T16270 Q800F | ||
| GB/T16270 Q890C | GB/T16270 Q890D | GB/T16270 Q890E | GB/T16270 Q890F | ||
| GB/T16270 Q960C | GB/T16270 Q960D | GB/T16270 Q960E | GB/T16270 Q960F | ||
| GB/T16270 Q500 | |||||




