Q460NC High-Strength Low-Alloy Steel Plate to GB/T 1591

Aug 27, 2025 Leave a message

What Is Q460NC Steel Plate?

Q460NC is a normalized low-alloy high-strength structural steel plate belonging to the GB/T 1591 family, the Chinese national standard for high strength low alloy structural steels. The grade guarantees a minimum yield strength of 460 MPa and is supplied in the normalized or normalized-rolled condition, so it is chosen for welded structures that need high strength together with a uniform, stable microstructure and a defined impact performance at 0 °C.

Because the plate is normalized rather than quenched and tempered, it is easier to weld and to form than quenched-and-tempered grades of the same strength class, and its properties remain more consistent after hot forming, flame straightening and stress relief. That is why normalized 460 MPa plate stays a default choice for heavy welded structures in general engineering and for equipment that operates at ambient temperature.

Grade Designation and Quality Grades

Q: the pinyin initial of qu, the character for yield strength.

460: the specified minimum yield strength, 460 MPa, measured as the upper yield strength of the plate.

N: the delivery condition, normalized or normalized rolled.

C: quality grade C, with Charpy impact testing at 0 °C.

Quality grades in this family run from C (0 °C) through D (-20 °C) to E (-40 °C). Q460NC is the C grade, so it suits ambient and mild service conditions. Where the lowest service temperature of a component falls below 0 °C, the D or E grade of the same strength class should be ordered instead: the strength guarantees are comparable, but the impact test temperature is lower.

Mechanical Properties of Q460NC Steel Plate

Thickness T (mm) Yield strength ReH min (MPa) Tensile strength Rm (MPa)
T ≤ 16 460 540-720
16 < T ≤ 40 440 540-720
40 < T ≤ 63 430 540-720
63 < T ≤ 80 410 540-720
80 < T ≤ 100 400 540-720
100 < T ≤ 150 380 530-710
150 < T ≤ 200 370 530-710
200 < T 370 510-690

The yield requirement drops from 460 MPa in the thinnest bracket to 370 MPa above 200 mm, a fall of about 20 %. The reason is metallurgical rather than commercial: heavy plate receives less rolling reduction per unit thickness and cools more slowly at the core, so the ferrite grain is coarser. Design calculations must therefore use the yield value of the thickness bracket actually ordered, not the headline 460 MPa figure.

Chemical Composition of Q460NC

Heat analysis per GB/T 1591-2018, weight per cent. Ranges are shown where both a minimum and a maximum apply; single values are maxima.

Element Limit (%) Element Limit (%)
C 0.20 max Ti 0.006-0.05
Si 0.60 max Cr 0.30 max
Mn 1.00-1.70 Ni 0.80 max
P 0.030 max Cu 0.40 max
S 0.030 max Mo 0.10 max
Nb 0.01-0.05 N 0.015 max
V 0.01-0.20 Als 0.015 min

Manganese is specified as a range rather than a maximum because it is the main solid-solution strengthener in a normalized steel; together with niobium, vanadium and titanium it delivers the 460 MPa class without pushing carbon above 0.20 %. The aluminium minimum guarantees a fully killed, fine-grained steel, which is essential for consistent normalizing response in heavy sections.

The quality grade is visible in the residual limits as well. A C-grade plate such as Q460NC allows phosphorus and sulphur of up to 0.030 % each and nitrogen up to 0.015 %. The E grade of the same strength class tightens phosphorus and sulphur to 0.025 % and 0.020 %, and because a minimum aluminium content is guaranteed, the nitrogen limit can be relaxed. When a project specifies a low impact test temperature, the tighter residual levels are part of what is being bought.

Delivery Condition, Fabrication and Applications

Normalized or normalized rolling is the standard delivery condition and is confirmed on the mill test certificate together with the heat analysis and the mechanical results. Hot forming, flame cutting, edge preparation and welding all respond predictably to a normalized plate, because the grain structure is uniform through the section.

Fabrication practice should follow the carbon equivalent of the actual heat rather than the grade alone. Thin plate welded with low heat input generally needs little or no preheat; heavy sections, high heat input and highly restrained joints need preheat, low-hydrogen consumables and a controlled interpass temperature. The plate is readily cut, drilled, milled and machined to drawing, and where a special application calls for tighter limits on a particular chemical element, the composition and the corresponding test requirements can be agreed before rolling. Thick joints that carry through-thickness strain should be ordered with Z-direction properties and ultrasonic testing specified alongside the grade.

Typical applications of Q460NC include general welded steel structures, heavy machinery frames, crane and lifting equipment, bridges and building structures in mild climates, transport and vehicle equipment, mining and material-handling machinery, and structural supports and platforms for industrial plant.

Frequently Asked Questions About Q460NC Steel Plate

Q: What is the difference between Q460NC and Q460NE?
The letters describe delivery condition and quality grade. Both grades are normalized, but C means Charpy impact testing at 0 °C while E means testing at -40 °C, and the E grade also carries tighter phosphorus and sulphur limits.

Q: Which standard covers Q460NC steel plate?
The Chinese national standard GB/T 1591, which governs high strength low alloy structural steels. Some orders add supplementary technical conditions for tighter element control or additional testing.

Q: What does the N in the grade mean?
N stands for normalized or normalized rolled delivery, meaning the plate is heat treated after rolling to refine the grain structure and stabilise the mechanical properties.

Q: What is the minimum yield strength by thickness?
460 MPa up to 16 mm, then 440, 430, 410 and 400 MPa through the 16-100 mm brackets, 380 MPa from 100 to 150 mm, and 370 MPa from 150 mm upwards.

Q: Is Q460NC suitable for welded structures?
Yes. Normalized delivery and a controlled carbon equivalent make the grade weldable with qualified procedures; preheat and interpass temperature are set from plate thickness and carbon equivalent, and heavy or restrained joints use low-hydrogen consumables.

Q: Can the plate be supplied with ultrasonic testing or Z-direction properties?
Yes. Ultrasonic testing classes and through-thickness classes can be specified on the order, and the plate can be supplied cut, bevelled, milled or machined to the required drawing.