What Q960E Is and Which Standard Covers It
Q960E is a quenched and tempered high strength structural steel plate. The designation follows the Chinese pattern: Q for the yield strength property, 960 for the minimum specified yield strength in MPa, and E for the quality class, which in this family denotes impact testing at -40 °C. The letter E is therefore a toughness statement, not a strength statement, and the same base strength is available in C, D and E quality classes with progressively lower impact test temperatures. The grade sits in the quenched and tempered high strength plate family, where the strength is developed by alloying plus a quench and temper cycle rather than by normalizing or thermomechanical rolling alone.
Mechanical Properties and Composition
Because 960 MPa is a demanding yield level, the composition combines a moderate carbon content with a hardenability package of manganese, chromium, nickel, molybdenum and boron.
| Parameter | Requirement |
|---|---|
| Yield strength (min) | 960 MPa |
| Tensile strength | 980-1150 MPa |
| Elongation | 10 % min |
| Impact test temperature | -40 °C |
| Impact energy (min) | 27 J |
| C | 0.20 % max |
| Si | 0.80 % max |
| Mn | 1.60 % max |
| P / S | 0.020 % max / 0.010 % max |
| CEV | typically 0.55-0.65 depending on thickness |
The yield to tensile ratio is high, which is normal for quenched and tempered plate and is why these grades are designed rather than substituted for a lower strength steel: the elongation of 10 % leaves limited plastic redistribution capacity, so welded connections are detailed to avoid strain concentration.
Delivery Condition and Thickness Range
Q960E is delivered in the quenched and tempered condition, and the certified mechanical properties apply to the plate as delivered. Any subsequent thermal cycle above the original tempering temperature, including post-weld heat treatment or hot forming, reduces strength, so the fabrication route must be agreed before the order is placed. Thickness is commonly available from 4 mm to 150 mm, and plate is normally ordered with a specified flatness class because high strength plate tends to distort more than structural plate of the same thickness during thermal cutting.
Applications
The grade is used where payload or lifting capacity depends on weight: crane booms and telescopic sections, concrete pump truck booms and outriggers, excavator and loader arms, mining truck and trailer frames, aerial work platform structures, wind turbine components, heavy transport equipment, and high-load nodes in steel structures such as transfer girders and bearing brackets. In gantry and mobile cranes, using 960 MPa plate instead of a 355 MPa structural plate can reduce the self weight of the boom by a substantial margin for the same load capacity, which directly increases the allowable payload.
Cutting, Forming and Welding
Cutting is by plasma, laser, waterjet or, for thinner plate, shearing, with thermal cut edges dressed to remove the hardened layer before welding or before the edge is cyclically loaded. Cold forming requires generous radii; heavy or small-radius forming is carried out warm, with the temperature held below the original tempering temperature, and the strength of formed areas is verified afterwards. Welding uses low-hydrogen consumables matched to the strength class in terms of the actual joint requirement, with preheat of 100-150 °C and a restricted heat input and interpass temperature to avoid both cold cracking and excessive softening. Post-weld heat treatment is generally not applied, because any treatment hot enough to relieve stress would also reduce the strength of the quenched and tempered plate; designs that expect high restraint are instead managed through welding sequence, symmetry and controlled assembly. Weld quality is verified by ultrasonic testing in accordance with the acceptance class agreed for the application, and hardness surveys across the heat-affected zone are used to confirm that the procedure is under control.
Quality Control and Ordering Points
Orders should state the grade and quality class, thickness and tolerance, flatness class, impact test requirement, carbon equivalent limit, maximum permitted heat input for welding, and the non-destructive testing acceptance class. Mill certification to EN 10204 type 3.1 is issued with heat analysis, tensile and impact results, and, where specified, hardness and bend results; type 3.2 with third-party witnessing is available. Traceability marking of heat number and plate identity is maintained through cutting so that the fabrication shop can match each part back to its certified plate.
Frequently Asked Questions
Q: What does the E in Q960E mean?
A: It is the quality class for impact toughness. E indicates testing at -40 °C with a minimum absorbed energy of 27 J in this high strength family.
Q: What is the tensile strength of Q960E plate?
A: The specified tensile range is 980-1150 MPa, paired with a minimum yield strength of 960 MPa and a minimum elongation of 10 %.
Q: Can Q960E be stress relieved after welding?
A: Normally not beneficial. Any thermal cycle hot enough to relieve the weld stress also tempers the plate and reduces its strength, so restraint and distortion are managed by welding sequence and pre-set instead.
Q: What preheat is used for welding?
A: Typically 100-150 °C with low-hydrogen consumables and a controlled heat input. The exact values are set by the qualified welding procedure for the joint type and thickness.
Q: Why is flatness specified separately?
A: High strength quenched and tempered plate distorts more than lower strength plate during thermal cutting and welding, so flatness is ordered as a defined class and inspected before fabrication.
Q: Which thickness range is available?
A: Standard production covers 4 mm to 150 mm, with the heavy end used mainly for crane and mining equipment structures.





