DIN EN 10025-6 S890Q is an ultra-high-strength structural steel plate supplied in the quenched and tempered (Q&T) condition. It is designed for applications requiring very high load-bearing capacity, weight optimization, and structural reliability, especially in heavy engineering and demanding environments.
This complete technical guide explains what S890Q steel is, its mechanical and chemical properties, fabrication behavior, processing challenges, and typical applications.
1. What Is DIN EN 10025-6 S890Q Steel?
S890Q is a high-strength non-alloy structural steel specified in DIN EN 10025-6, which covers quenched and tempered structural steels with minimum yield strengths from 460 MPa up to 960 MPa.
"S" – Structural steel
"890" – Minimum yield strength of 890 MPa
"Q" – Delivery condition: Quenched and Tempered
Despite being described as non-alloy in the standard classification, S890Q uses micro-alloying and controlled heat treatment to achieve its exceptional mechanical performance.

Chemical Composition (Typical, % Max)
EN 10025-6 specifies maximum limits rather than fixed values to guarantee performance and weldability.
| Element | Max % |
|---|---|
| Carbon (C) | ≤ 0.20 |
| Silicon (Si) | ≤ 0.80 |
| Manganese (Mn) | ≤ 1.70 |
| Phosphorus (P) | ≤ 0.020 |
| Sulfur (S) | ≤ 0.010 |
| Chromium (Cr) | ≤ 1.50 |
| Nickel (Ni) | ≤ 2.00 |
| Molybdenum (Mo) | ≤ 0.70 |
Mechanical Properties of S890Q Steel Plate
Mechanical properties may vary slightly with thickness, but typical EN 10025-6 requirements are as follows:
| Property | Requirement |
|---|---|
| Minimum Yield Strength | ≥ 890 MPa |
| Tensile Strength | 940 – 1100 MPa |
| Elongation (A5) | ≥ 10% |
| Impact Test | −40°C (Charpy V-notch) |
| Hardness (Typical) | 290 – 350 HB |
Weldability of S890Q Steel Plate
Although S890Q is an ultra-high-strength steel, it offers better weldability than higher grades such as S960Q, provided correct procedures are followed.
Recommended Welding Practices:
- Use low-hydrogen welding consumables
- Apply preheating, especially for thick plates
- Control heat input to prevent HAZ softening or excessive hardness
- Avoid high restraint during welding
Typical Welding Challenges:
- Hydrogen-induced cracking risk if preheating is ignored
- Increased residual stress compared to lower-strength steels
- Strict control required for interpass temperature
- With proper planning, S890Q performs reliably in large welded structures.

Cutting, Forming & Fabrication Behavior
Cutting
Flame, plasma, and laser cutting are feasible
HAZ hardness may increase after thermal cutting
Edge grinding is recommended for fatigue-critical parts
Bending & Forming
Higher springback than conventional structural steels
Larger minimum bending radius required
Cold forming is possible with correct tooling and process control
Practical Insight:
S890Q offers better fabrication tolerance than S960Q, making it more suitable for complex structures.
Typical Applications of S890Q Steel Plate
S890Q is widely used in weight-critical and heavy-load applications, including:
Crane booms and crane frames
Heavy construction machinery
Mining and quarry equipment
Offshore and marine structures
High-strength load-bearing frames
Specialized bridges and steel structures

Why Choose S890Q Steel Plate from GNEE Steel?
- EN 10025-6 compliant production
- Stable Q&T heat treatment
- Wide size availability
- Export experience in heavy engineering projects
- Technical support for welding and fabrication
Conclusion
DIN EN 10025-6 S890Q non-alloy structural steel plate is a proven solution for projects requiring:
- Extremely high strength
- Weight reduction
- Reliable toughness
- Controlled fabrication behavior
- For engineers, it enables efficient structural design.
📩 Contact GNEE Steel today for technical consultation, pricing, and customized S890Q solutions.
Q1: What is S890Q steel plate?
A:S890Q is a high-strength structural steel plate according to EN 10025-6, supplied in quenched and tempered (Q) condition, with a minimum yield strength of 890 MPa.
Q2: What is the material number of S890Q?
A:The European material number for S890Q is 1.8940.
Q3: Is S890Q considered non-alloy steel?
A:Yes. Under EN classification, S890Q is listed as non-alloy structural steel, although small alloying elements are added for strength and toughness control.
Q4: What thickness range is available for S890Q steel plate?
A:Common supply thickness ranges from 6 mm to 150 mm, depending on mill capability and standard requirements.
Q5: What are the mechanical properties of S890Q?
A:
Yield strength: ≥ 890 MPa (≤ 50 mm)
Tensile strength: 940–1100 MPa
Elongation: ≥ 11%
Impact test: ≥ 30 J at −20°C
Q6: Can S890Q steel be welded easily?
A:Yes, S890Q has good weldability, but welding must follow controlled procedures, including proper heat input, preheating (if required), and suitable filler materials.
Q7: What is the difference between S890Q and S890QL?
A:S890QL offers better low-temperature impact toughness than S890Q and is typically specified for colder environments or critical structures.
Q8: What are typical applications of S890Q steel plate?
A:S890Q is widely used in:
Cranes and lifting equipment
Bridges and heavy structures
Mining and earthmoving machinery
Wind power and offshore structures
Heavy-duty vehicle frames
Q9: Can S890Q replace S690Q to reduce weight?
A:Yes. Using S890Q instead of S690Q allows significant weight reduction while maintaining or increasing load capacity, which is especially valuable for mobile equipment.
Q10: What inspection and certificates are required for S890Q?
A:Standard supply includes EN 10204 3.1 MTC.
3.2 certificates, ultrasonic testing (UT), and third-party inspection (SGS, BV, TUV) are available upon request.
Q11: Is S890Q suitable for pressure vessel applications?
A:No. S890Q is a structural steel, not designed for pressure vessel or boiler applications. Pressure vessel steels must comply with specific PV standards such as EN 10028 or ASME.
Q12: What delivery condition is required for S890Q steel plate?
A:S890Q must be supplied in quenched and tempered (Q) condition as per EN 10025-6.
Q13: Can you cut or machine S890Q steel plate?
A:Yes. Flame cutting, plasma cutting, and machining are possible with controlled parameters to maintain material properties.
Q14: Does S890Q steel require special storage or handling?
A:Standard dry storage is sufficient. Surface protection can be added for long-term outdoor storage.
| Grades Of Carbon and Low-alloy High-strength Steels Supplied By GNEE | |||||
| ASTM/ASME | ASTM A36/A36M | ASTM A36 | |||
| ASTM A283/A283M | ASTM A283 Grade A | ASTM A283 Grade B | ASTM A283 Grade C | ASTM A283 Grade D | |
| ASTM A514/A514M | ASTM A514 Grade A | ASTM A514 Grade B | ASTM A514 Grade C | ASTM A514 Grade E | |
| ASTM A514 Grade F | ASTM A514 Grade H | ASTM A514 Grade J | ASTM A514 Grade K | ||
| ASTM A514 Grade M | ASTM A514 Grade P | ASTM A514 Grade Q | ASTM A514 Grade R | ||
| ASTM A514 Grade S | ASTM A514 Grade T | ||||
| ASTM A572/A572M | ASTM A572 Grade 42 | ASTM A572 Grade 50 | ASTM A572 Grade 55 | ASTM A572 Grade 60 | |
| ASTM A572 Grade 65 | |||||
| ASTM A573/A573M | ASTM A573 Grade 58 | ASTM A573 Grade 65 | ASTM A573 Grade 70 | ||
| ASTM A588/A588M | ASTM A588 Grade A | ASTM A588 Grade B | ASTM A588 Grade C | ASTM A588 Grade K | |
| ASTM A633/A633M | ASTM A633 Grade A | ASTM A633 Grade C | ASTM A633 Grade D | ASTM A633 Grade E | |
| ASTM A656/A656M | ASTM A656 Grade 50 | ASTM A656 Grade 60 | ASTM A656 Grade 70 | ASTM A656 Grade 80 | |
| ASTM A709/A709M | ASTM A709 Grade 36 | ASTM A709 Grade 50 | ASTM A709 Grade 50S | ASTM A709 Grade 50W | |
| ASTM A709 Grade HPS 50W | ASTM A709 Grade HPS 70W | ASTM A709 Grade 100 | ASTM A709 Grade 100W | ||
| ASTM A709 Grade HPS 100W | |||||
| ASME SA36/SA36M | ASME SA36 | ||||
| ASME SA283/SA283M | ASME SA283 Grade A | ASME SA283 Grade B | ASME SA283 Grade C | ASME SA283 Grade D | |
| ASME SA514/SA514M | ASME SA514 Grade A | ASME SA514 Grade B | ASME SA514 Grade C | ASME SA514 Grade E | |
| ASME SA514 Grade F | ASME SA514 Grade H | ASME SA514 Grade J | ASME SA514 Grade K | ||
| ASME SA514 Grade M | ASME SA514 Grade P | ASME SA514 Grade Q | ASME SA514 Grade R | ||
| ASME SA514 Grade S | ASME SA514 Grade T | ||||
| ASME SA572/SA572M | ASME SA572 Grade 42 | ASME SA572 Grade 50 | ASME SA572 Grade 55 | ASME SA572 Grade 60 | |
| ASME SA572 Grade 65 | |||||
| ASME SA573/SA573M | ASME SA573 Grade 58 | ASME SA573 Grade 65 | ASME SA573 Grade 70 | ||
| ASME SA588/SA588M | ASME SA588 Grade A | ASME SA588 Grade B | ASME SA588 Grade C | ASME SA588 Grade K | |
| ASME SA633/SA633M | ASME SA633 Grade A | ASME SA633 Grade C | ASME SA633 Grade D | ASME SA633 Grade E | |
| ASME SA656/SA656M | ASME SA656 Grade 50 | ASME SA656 Grade 60 | ASME SA656 Grade 70 | ASME SA656 Grade 80 | |
| ASME SA709/SA709M | ASME SA709 Grade 36 | ASME SA709 Grade 50 | ASME SA709 Grade 50S | ASME SA709 Grade 50W | |
| ASME SA709 Grade HPS 50W | ASME SA709 Grade HPS 70W | ASME SA709 Grade 100 | ASME SA709 Grade 100W | ||
| ASME SA709 Grade HPS 100W | |||||
| EN10025 | EN10025-2 | EN10025-2 S235J0 | EN10025-2 S275J0 | EN10025-2 S355J0 | EN10025-2 S355K2 |
| EN10025-2 S235JR | EN10025-2 S275JR | EN10025-2 S355JR | EN10025-2 S420J0 | ||
| EN10025-2 S235J2 | EN10025-2 S275J2 | EN10025-2 S355J2 | |||
| EN10025-3 | EN10025-3 S275N | EN10025-3 S355N | EN10025-3 S420N | EN10025-3 S460N | |
| EN10025-3 S275NL | EN10025-3 S355NL | EN10025-3 S420NL | EN10025-3 S460NL | ||
| EN10025-4 | EN10025-4 S275M | EN10025-4 S355M | EN10025-4 S420M | EN10025-4 S460M | |
| EN10025-4 S275ML | EN10025-4 S355ML | EN10025-4 S420ML | EN10025-4 S460ML | ||
| EN10025-6 | EN10025-6 S460Q | EN10025-6 S460QL | EN10025-6 S460QL1 | EN10025-6 S500Q | |
| EN10025-6 S500QL | EN10025-6 S500QL1 | EN10025-6 S550Q | EN10025-6 S550QL | ||
| EN10025-6 S550QL1 | EN10025-6 S620Q | EN10025-6 S620QL | EN10025-6 S620QL1 | ||
| EN10025-6 S690Q | EN10025-6 S690QL | EN10025-6 S690Q1 | EN10025-6 S890Q | ||
| EN10025-6 S890QL | EN10025-6 S890QL1 | EN10025-6 S960Q | EN10025-6 S960QL | ||
| EN 10149 | EN 10149-2 | S315MC | S355MC | S420MC | S460MC |
| S500MC | S550MC | S600MC | S650MC | ||
| S700MC | S900MC | S960MC | |||
| JIS | JIS G3101 | JIS G3101 SS330 | JIS G3101 SS400 | JIS G3101 SS490 | JIS G3101 SS540 |
| JIS G3106 | JIS G3106 SM400A | JIS G3106 SM400B | JIS G3106 SM400C | JIS G3106 SM490A | |
| JIS G3106 SM490YA | JIS G3106 SM490B | JIS G3106 SM490YB | JIS G3106 SM490C | ||
| JIS G3106 SM520B | JIS G3106 SM520C | JIS G3106 SM570 | |||
| DIN | DIN 17100 | DIN17100 St52-3 | DIN17100 St37-2 | DIN17100 St37-3 | DIN17100 RSt37-2 |
| DIN17100 USt37-2 | |||||
| DIN 17102 | DIN17102 StE315 | DIN17102 EStE315 | DIN17102 TStE315 | DIN17102 WStE315 | |
| DIN17102 StE355 | DIN17102 EStE355 | DIN17102 TStE355 | DIN17102 WStE355 | ||
| DIN17102 StE380 | DIN17102 EStE380 | DIN17102 TStE380 | DIN17102 WStE380 | ||
| DIN17102 StE420 | DIN17102 EStE420 | DIN17102 TStE420 | DIN17102 WStE420 | ||
| DIN17102 StE460 | DIN17102 EStE460 | DIN17102 TStE460 | DIN17102 WStE460 | ||
| DIN17102 StE500 | DIN17102 EStE500 | DIN17102 TStE500 | DIN17102 WStE500 | ||
| DIN17102 EStE285 | |||||
| GB | GB/T700 | GB/T700 Q235A | GB/T700 Q235B | GB/T700 Q235C | GB/T700 Q235D |
| GB/T700 Q275 | |||||
| GB/T1591 | GB/T1591 Q345A | GB/T1591 Q390A | GB/T1591 Q420A | GB/T1591 Q420E | |
| GB/T1591 Q345B | GB/T1591 Q390B | GB/T1591 Q420B | GB/T1591 Q460C | ||
| GB/T1591 Q345C | GB/T1591 Q390C | GB/T1591 Q420C | GB/T1591 Q460D | ||
| GB/T1591 Q345D | GB/T1591 Q390D | GB/T1591 Q420D | GB/T1591 Q460E | ||
| GB/T1591 Q345E | GB/T1591 Q390E | ||||
| GB/T16270 | GB/T16270 Q550C | GB/T16270 Q550D | GB/T16270 Q550E | GB/T16270 Q550F | |
| GB/T16270 Q620C | GB/T16270 Q620D | GB/T16270 Q620E | GB/T16270 Q620F | ||
| GB/T16270 Q690C | GB/T16270 Q690D | GB/T16270 Q690E | GB/T16270 Q690F | ||
| GB/T16270 Q800C | GB/T16270 Q800D | GB/T16270 Q800E | GB/T16270 Q800F | ||
| GB/T16270 Q890C | GB/T16270 Q890D | GB/T16270 Q890E | GB/T16270 Q890F | ||
| GB/T16270 Q960C | GB/T16270 Q960D | GB/T16270 Q960E | GB/T16270 Q960F | ||
| GB/T16270 Q500 | |||||




