Two standards, two very different service duties
P295GH is a European pressure vessel steel plate supplied under EN 10028-2 in the normalized delivery condition. The letters identify a steel for pressure purposes with a minimum yield strength of 295 MPa at room temperature, and the grade is used for boilers, pressure vessels, heat exchangers and other equipment that operates at elevated temperature where strength retention and creep behaviour matter.
Q295GNH is a Chinese weathering structural steel plate supplied under GB/T 4171. The designation says that the steel has a minimum yield strength of 295 MPa, that it is a high-phosphorus atmospheric-corrosion-resistant grade, and that it belongs to the weathering steel family. It is used in welded and bolted structures - bridges, buildings, towers, containers and rolling stock - where the protective rust layer does the corrosion-resistance work.
Put simply: P295GH is a pressure-retaining steel chosen for hot service, and Q295GNH is an exposed-structure steel chosen for weather resistance.
Chemical composition compared
| Element | P295GH (EN 10028-2) | Q295GNH (GB/T 4171) |
| C, max | 0.20 | 0.12 |
| Si | 0.40 max | 0.20-0.40 |
| Mn | 0.90-1.50 | 0.20-0.60 |
| P, max | 0.025 | 0.07-0.15 |
| S, max | 0.015 | 0.035 |
| Al, min | 0.020 | - |
| N, max | 0.012 | - |
| Cu | 0.30 max | 0.25-0.55 |
| Cr | 0.30 max | Weathering addition per GB/T 4171 |
| Mo | 0.08 max | - |
| Ni | 0.30 max | - |
| Nb | 0.020 max | - |
| Ti | 0.03 max | 0.15 max |
| V | 0.02 max | - |
The compositions point in opposite directions. P295GH is a low-phosphorus, low-sulphur, fully killed fine-grain steel with a minimum aluminium content of 0.020 %; cleanliness is essential because the plate has to carry pressure at temperature. Q295GNH deliberately keeps phosphorus in the range 0.07-0.15 % and adds copper in the range 0.25-0.55 %, because that combination is what produces the dense, adherent oxide layer that slows further atmospheric attack. Manganese is much lower in Q295GNH than in P295GH, which reflects the different strength route: solid-solution and corrosion chemistry instead of a manganese-controlled pressure-grade microstructure.
Both grades use the same carbon equivalent expression: Ceq = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15, expressed in percent. For welding, that number is the practical guide to preheat selection, and it is worth noting that the copper and phosphorus in Q295GNH can make the heat-affected zone more sensitive to procedure control.
Mechanical properties of P295GH
P295GH is delivered normalized, and its minimum yield strength falls as plate thickness rises, which is typical for normalized pressure vessel steels.
| Thickness, mm | Yield strength, min MPa | Tensile strength, MPa | Elongation, min % |
| up to 16 | 295 | 460-580 | 21 |
| 16 to 40 | 290 | 460-580 | 21 |
| 40 to 60 | 285 | 460-580 | 21 |
| 60 to 100 | 260 | 460-580 | 21 |
| 100 to 150 | 235 | 440-570 | 21 |
| 150 to 250 | 220 | 430-570 | 21 |
Charpy V-notch impact testing applies to this grade; the minimum average absorbed energy required for P295GH is 27 J at the agreed test temperature, with higher values normally applied at room temperature. Because the grade is used in pressure equipment, the impact regime, the test temperature and the acceptance criteria are all fixed on the purchase order and supported by an inspection certificate.
Mechanical properties of Q295GNH
| Thickness, mm | Yield strength, min MPa | Tensile strength, MPa | Elongation, min % | Delivery condition |
| up to 6 | 295 | 390 | 24 | Hot rolled |
| above 6 | 260 | 390 | 27 | Hot rolled |
Q295GNH is registered at a lower minimum yield strength than its name suggests once thickness increases, and the elongation values of 24 % and 27 % reflect a soft, formable structural plate. The strength level is deliberately moderate because the grade is designed to be bent, punched and bolted into fabricated structures rather than to resist internal pressure.
Corrosion and temperature behaviour
Weathering steels such as Q295GNH rely on wet-dry cycling. In an exposed atmosphere the surface first rusts, then the alloying elements concentrate in the rust layer and it becomes dense and protective, slowing the corrosion rate to a small fraction of that of ordinary carbon steel. That mechanism does not work when the steel is permanently wet, buried, immersed in water or exposed to heavy chloride or acid attack, which is why weathering steel is specified for exposed bridges, towers, frames and containers.
P295GH takes the opposite approach. It contains no deliberate copper or phosphorus addition; instead it relies on low phosphorus, low sulphur and a normalized fine-grain structure to keep strength and ductility at elevated service temperature in boilers, vessels, heat exchangers and steam systems. Atmospheric corrosion resistance is not its design purpose, so it normally needs paint, coating or cladding for outdoor exposure.
Welding, forming and ordering notes
Welding P295GH: match the filler to the base metal tensile range, use a qualified procedure, and control heat input so the normalized structure and impact properties are preserved. Post-weld heat treatment is normally applied to pressure equipment to relieve residual stress.
Welding Q295GNH: use low-hydrogen consumables, control the copper and phosphorus effect through the welding procedure, and keep the weld sound because a poorly formed joint becomes the first place the protective rust layer fails.
Forming: both grades are ductile and readily cold formed. Q295GNH is often bent to large radii for container and structural sections, while P295GH is formed into vessel shells.
Ordering: state the standard, the grade, the delivery condition, the plate thickness, the impact test requirement and the required certificate. The two grades are not interchangeable, because one is a pressure steel and the other is a weathering structural steel.
Frequently asked questions
Q: Is P295GH or Q295GNH stronger?
P295GH has the higher tensile strength, in the range 460-580 MPa for plates up to 100 mm thick. Q295GNH is registered at a minimum tensile strength of 390 MPa, so its strength is deliberately moderate.
Q: Can Q295GNH be used for pressure vessels?
No. Q295GNH is a weathering structural steel under GB/T 4171, not a pressure vessel grade. Vessels and boilers should be specified to EN 10028-2 or another recognised pressure equipment standard.
Q: Why does Q295GNH contain so much phosphorus?
Phosphorus in the range 0.07-0.15 % combined with copper in the range 0.25-0.55 % is what makes the rust layer protective on this high-phosphorus weathering grade. In a pressure steel that same phosphorus level would be unacceptable because it damages toughness.
Q: What happens to P295GH strength as the plate gets thicker?
Minimum yield strength falls with thickness, from 295 MPa up to 16 mm to 220 MPa in the 150-250 mm range, while tensile strength drops from 460-580 MPa to 430-570 MPa at the heaviest thicknesses.
Q: Does weathering steel need painting?
Q295GNH is normally left unpainted in the right environment so that the protective rust layer can form. Where it is permanently wet, buried, or exposed to salt or chemicals, painting or coating is required instead.
Q: What delivery condition does each grade have?
P295GH is supplied normalized. Q295GNH is normally supplied hot rolled, with the mechanical values in the table applying to that condition.
Q: How is carbon equivalent calculated for these plates?
Ceq = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15, in percent. It is used to set preheat and welding procedure requirements, and the copper content of Q295GNH makes this check particularly important.






