What Is BV AH32 Steel Plate?
BV AH32 is a high-strength hull structural steel grade within the Bureau Veritas rule system for the classification of steel ships. In this notation the letter A defines the impact test temperature of the grade, which is 0 °C, while the number 32 denotes a minimum yield strength of 315 MPa. The grade belongs to the same family as the ASTM A131 AH32 hull steel and is produced to the chemical and mechanical requirements applied to high-strength shipbuilding plate.
AH32 plate is supplied for the primary structure of ships and offshore units, where the design must combine a high strength-to-weight ratio with proven impact toughness and weldability. Compared with ordinary hull steel of grade A or B, the higher yield strength of AH32 allows designers to reduce scantlings without losing structural safety, which is why the grade is common in upper decks, hatch coamings and other weight-sensitive, highly stressed regions.
Chemical Composition
The table below gives the maximum or specified ranges for the elements controlled in the heat analysis of BV AH32 plate.
| Element | C max | Si | Mn | P max | S max | Al min |
|---|---|---|---|---|---|---|
| Content (%) | 0.18 | 0.10 - 0.50 | 0.90 - 1.60 | 0.035 | 0.035 | 0.015 |
Small additions of niobium, vanadium, titanium, copper, chromium, nickel and molybdenum are used to refine the grain and support the strength target:
Nb: 0.02 - 0.05 %
V: 0.05 - 0.10 %
Ti: 0.02 % maximum
Cu: 0.35 % maximum
Cr: 0.20 % maximum
Ni: 0.40 % maximum
Mo: 0.08 % maximum
A minimum aluminium content of 0.015 % is specified to ensure fine-grain practice through aluminium nitride formation. Grain refinement is what converts the strength obtained from manganese and microalloying into usable toughness, and it is the reason a well-produced AH32 plate can absorb impact energy at 0 °C even though its yield strength is more than one and a half times that of mild steel.
Mechanical Properties and Impact Testing
| Thickness | Min yield (MPa) | Tensile (MPa) | Min elongation (%) | Charpy test temp. | Energy 1 transverse (J) | Energy 2 longitudinal (J) |
|---|---|---|---|---|---|---|
| t ≤ 50 mm | 315 | 440 - 570 | 22 | 0 °C | 22 | 31 |
| 50 < t ≤ 70 mm | 315 | 440 - 570 | 22 | 0 °C | 26 | 38 |
| 70 < t ≤ 100 mm | 315 | 440 - 570 | 22 | 0 °C | 31 | 46 |
Charpy V-notch specimens are taken transverse and longitudinal to the rolling direction, and the required energy rises with plate thickness because thicker sections are tested with larger specimens. The 0 °C test temperature is the defining feature of the A notation; where service conditions demand a lower testing temperature, the same strength level is ordered in the D (minus 20 °C) or E (minus 40 °C) variants of the family.
Carbon Equivalent and Weldability
Weldability of a high-strength hull plate is controlled mainly through the carbon and carbon equivalent levels. Two expressions are used in practice:
Carbon equivalent: Ceq = C + Mn/6 + (Cr + Mo + V)/5 + (Ni + Cu)/15
Crack sensitivity: Pcm = C + Si/30 + Mn/20 + Cu/20 + Ni/60 + Cr/20 + Mo/15 + V/10 + 5B
The low carbon ceiling of 0.18 % keeps both values modest for a 315 MPa yield steel, which allows conventional arc welding with low-hydrogen consumables. For thicker sections and for restrained joints, a moderate preheat and controlled interpass temperature are applied, and matching strength consumables are selected so that the welded joint reaches the base-metal strength without a loss of toughness. Post-weld heat treatment is only used where the design or a specific rule requirement calls for it, since excessive heat input can coarsen the grain structure of the heat-affected zone.
Applications in Shipbuilding and Offshore Structures
Deck plating, main deck and strength deck structures of cargo ships and bulk carriers
Hull side shell and bottom shell in highly stressed regions
Hatch coamings, hatch covers and deck girders
Offshore platform decks, pontoons and support structures
Ship repair and conversion work where an equivalent grade to the original class-approved steel is required
Barges, dredgers and heavy-duty marine floating equipment
All plate is supplied in a normalized or controlled-rolled condition so that the specified strength and toughness are reproduced through the full thickness and along the full length of the coil or plate. Each order is normally accompanied by a class certificate linking the heat number, the mechanical test results and the impact test data to the delivered plate.
FAQ
Q: What do the letters and numbers in BV AH32 mean?
A indicates that the steel is impact tested at 0 °C and 32 indicates a minimum yield strength of 315 MPa. The BV prefix shows that the grade is certified within the Bureau Veritas classification rules for shipbuilding steel.
Q: Is AH32 the same as ASTM A131 AH32?
The two designations describe the same 315 MPa minimum yield, 0 °C impact-tested hull steel. Chemical and mechanical requirements are aligned between the classification society rules and the ASTM A131 hull steel specification, with the certificate issued under the relevant scheme.
Q: How is AH32 different from AH36?
AH36 has the same impact test temperature of 0 °C and the same family of chemistry, but a higher minimum yield strength of 355 MPa. AH32 is the lighter of the two strength levels and is often used where a 315 MPa design stress is sufficient.
Q: What heat treatment condition is the plate supplied in?
AH32 plate is normally supplied normalized or in a controlled-rolled condition. Both routes are intended to deliver a uniform ferrite-pearlite microstructure with fine grains so that the impact energy requirement is met throughout the thickness.
Q: Which impact energies must be met?
For plate up to 50 mm thick the minimum transverse Charpy V-notch energy is 22 J at 0 °C, rising to 26 J for thicknesses above 50 mm and up to 70 mm, and 31 J for thicknesses above 70 mm up to 100 mm.
Q: Can AH32 be welded without preheat?
For thin sections welded with low-hydrogen consumables and a low carbon equivalent, preheat may be omitted where the classification rules and approved welding procedure permit it. Thicker, highly restrained joints normally require a specified preheat.




