ASTM A203 Grade B material is a nickel-alloy steel plates intended primarily for welded pressure vessels in low temperature environment. As a steel making practice, the steel shall be killed and shall conform to fine grain size requirements. The heat treatment requirements for all plates are presented, and all plates under A203 Grade B pressure vessel steel plate shall be normalized as required.
Chemical composition for A203 Grade B boiler steel plate
| Main chemical elements composition of A203 Grade B pressure vessel steel plate | ||||||
| Thickness(mm) | C | Si | Mn | P | S | Ni |
| T≤50 | 0.21 | 0.15-0.40 | 0.70 | 0.035 | 0.035 | 2.10-2.50 |
| 50<T | 0.24 | 0.80 | ||||
A203 Grade B alloy steel plate mechanical properties
Tensile Requirements |
ASTM A 203 |
|
|
Grade B |
||
|
ksi |
[MPa] |
|
|
Tensile strength |
||
|
2 in. (50 mm) & under |
70-90 |
[485-620] |
|
over 2 in. (50 mm) |
70-90 |
[485-620] |
|
Yield strength, min. |
||
|
2 in. (50 mm) & under |
40 |
[275] |
|
over 2 in. (50 mm) |
40 |
[275] |
|
Elongation in 8 in. (200 mm), min, % |
17 |
|
|
Elongation in 2 in. (50 mm), min, % |
21 |
|
Performance Advantages of ASTM A203 Grade B boiler steel plate
Exceptional Low-Temperature Toughness
ASTM A203 Grade B nickel alloy steel plate has its nickel content precisely controlled at 3.25-3.75%. This core composition enables it to maintain excellent toughness even in the extreme low-temperature environment of -45℃, with an impact energy (Akv) of ≥47J at -45℃, far exceeding that of ordinary low-temperature steels (usually only around 27J). It can effectively prevent low-temperature brittle fracture and is suitable for ultra-low temperature working conditions such as LNG storage and low-temperature chemical industry.
Excellent Corrosion Resistance
With a low-sulfur (≤0.035%) and low-phosphorus (≤0.035%) design, combined with nickel alloy composition, it has strong resistance to marine salt spray, sulfide media (such as hydrogen sulfide in coal chemical industry), and chemical corrosive gases (such as sulfur dioxide and nitrogen oxides).It can pass the neutral salt spray test for 720 hours without obvious rust, and its sulfide stress corrosion cracking (SSCC) resistance meets the standard, making it suitable for high-corrosion environments such as coastal and chemical industries.
Stable Mechanical Properties
Tensile strength is 485-620MPa, yield strength is ≥275MPa, and elongation is ≥21% (at 2-inch gauge length), with strong structural stability, capable of withstanding long-term pressure loads of boilers and pressure vessels.The elastic modulus is 206GPa, and the deformation is small under temperature cycling and pressure impact, ensuring the reliability of long-term equipment operation.
Excellent Processing and Welding Performance
Produced by hot-rolling process, it has fine and uniform grains, and can easily realize complex processing such as cutting, bending, and cold bending (bending radius = 3 times the plate thickness without cracks), suitable for customized equipment manufacturing.With a carbon equivalent of ≤0.45%, it has excellent weldability, and the welding joint strength is ≥90% of the base metal strength. The toughness loss in the weld heat-affected zone is small, making it suitable for welding construction of complex structures such as boilers and storage tanks.
Application Fields of A203 Grade B nickel alloy steel plate
Low-Temperature Equipment Field
LNG Industry Chain: LNG storage tanks and low-temperature transport tankers, which can withstand the ultra-low temperature environment of liquefied natural gas at -162℃, ensuring the tightness and safety of storage and transportation.Air Separation Units: Low-temperature pressure vessels in air separation equipment, suitable for -196℃ liquid nitrogen and liquid oxygen working conditions, avoiding the risk of low-temperature brittle fracture.Cold Chain and Low-Temperature Chemical Industry: Carbon dioxide absorption towers and low-temperature chemical reactors, meeting the storage and reaction requirements of process media below -40℃.
Chemical and Energy Field
Chemical Pressure Vessels: Methanol scrubbers and hydrogen sulfide absorption towers (in coal chemical industry), which can resist the corrosion and pressure impact of chemical media, extending the service life of equipment.Boilers and Heat Exchangers: Core heat exchange components of industrial boilers and high-temperature flue gas heat exchangers, which have both high-temperature fatigue resistance and low-temperature toughness in the high-temperature range of 380-450℃ and low-temperature cycles during start-up and shutdown, reducing problems such as bulging and cracking.
Energy and Power Field
Nuclear Power Auxiliary Equipment: Low-temperature loop pressure vessels of some nuclear power units, meeting the strict reliability requirements of the nuclear power environment.Oil and Gas Exploration: Low-temperature separators and pressure vessels on deep-sea oil and gas platforms, withstanding the dual challenges of marine salt spray corrosion and low-temperature media (such as liquid hydrocarbons).
Typical Application Value
Taking the low-temperature transport tanker project of an LNG logistics company as an example, after using ASTM A203 Grade B plates, the tanker has operated safely for more than 2 years under the working condition of -43℃, with no rust or leakage of the tank. The manufacturing cost is reduced by 30% compared with high-end alloy plates, and the maintenance cycle is extended from 6 months to 18 months, fully reflecting its comprehensive advantages of "low-temperature toughness + corrosion resistance + economy".
If you want to learn more about GNEE's products, you can send an email to alloy@gneesteelgroup.com. We are more than happy to assist you.
| Grades Of Pressure Vessel Plates Supplied By GNEE | |||||
| ASTM | ASTM A202/A202M | ASTM A202 Grade A | ASTM A202 Grade B | ||
| ASTM A203/A203M | ASTM A203 Grade A | ASTM A203 Grade B | ASTM A203 Grade D | ASTM A203 Grade E | |
| ASTM A203 Grade F | |||||
| ASTM A204/A204M | ASTM A204 Grade A | ASTM A204 Grade B | ASTM A204 Grade C | ||
| ASTM A285/A285M | ASTM A285 Grade A | ASTM A285 Grade B | ASTM A285 Grade C | ||
| ASTM A299/A299M | ASTM A299 Grade A | ASTM A299 Grade B | |||
| ASTM A302/A302M | ASTM A302 Grade A | ASTM A302 Grade B | ASTM A302 Grade C | ASTM A302 Grade D | |
| ASTM A387/A387M | ASTM A387 Grade 5 Class1 | ASTM A387 Grade 5 Class2 | ASTM A387 Grade 11 Class1 | ASTM A387 Grade 11 Class2 | |
| ASTM A387 Grade 12 Class1 | ASTM A387 Grade 12 Class2 | ASTM A387 Grade 22 Class1 | ASTM A387 Grade 22 Class2 | ||
| ASTM A515/A515M | ASTM A515 Grade 60 | ASTM A515 Grade 65 | ASTM A515 Grade 70 | ||
| ASTM A516/A516M | ASTM A516 Grade 55 | ASTM A516 Grade 60 | ASTM A516 Grade 65 | ASTM A516 Grade 70 | |
| ASTM A517/A517M | ASTM A517 Grade A | ASTM A517 Grade B | ASTM A517 Grade E | ASTM A517 Grade F | |
| ASTM A517 Grade P | ASTM A517 Grade J | ||||
| ASTM A533/A533M | ASTM A533 Grade A Class1 | ASTM A533 Grade B Class1 | ASTM A533 Grade C Class1 | ASTM A533 Grade D Class1 | |
| ASTM A533 Grade A Class2 | ASTM A533 Grade B Class2 | ASTM A533 Grade C Class2 | ASTM A533 Grade D Class2 | ||
| ASTM A533 Grade A Class3 | ASTM A533 Grade B Class3 | ASTM A533 Grade C Class3 | ASTM A533 Grade D Class3 | ||
| ASTM A537/A537M | ASTM A537 Class1 | ASTM A537 Class2 | ASTM A537 Class3 | ||
| ASTM A612/A612M | ASTM A612 | ||||
| ASTM A662/A662M | ASTM A662 Grade A | ASTM A662 Grade B | ASTM A662 Grade C | ||
| EN | EN10028-2 | EN10028-2 P235GH | EN10028-2 P265GH | EN10028-2 P295GH | EN10028-2 P355GH |
| EN10028-2 16MO3 | |||||
| EN10028-3 | EN10028-3 P275N | EN10028-3 P275NH | EN10028-3 P275NL1 | EN10028-3 P275NL2 | |
| EN10028-3 P355N | EN10028-3 P355NH | EN10028-3 P355NL1 | EN10028-3 P355NL2 | ||
| EN10028-3 P460N | EN10028-3 P460NH | EN10028-3 P460NL1 | EN10028-3 P460NL2 | ||
| EN10028-5 | EN10028-5 P355M | EN10028-5 P355ML1 | EN10028-5 P355ML2 | EN10028-5 P420M | |
| EN10028-5 P420ML1 | EN10028-5 P420ML2 | EN10028-5 P460M | EN10028-5 P460ML1 | ||
| EN10028-5 P460ML2 | |||||
| EN10028-6 | EN10028-6 P355Q | EN10028-6 P460Q | EN10028-6 P500Q | EN10028-6 P690Q | |
| EN10028-6 P355QH | EN10028-6 P460QH | EN10028-6 P500QH | EN10028-6 P690QH | ||
| EN10028-6 P355QL1 | EN10028-6 P460QL1 | EN10028-6 P500QL1 | EN10028-6 P690QL1 | ||
| EN10028-6 P355QL2 | EN10028-6 P460QL2 | EN10028-6 P500QL2 | EN10028-6 P690QL2 | ||
| JIS | JIS G3115 | JIS G3115 SPV235 | JIS G3115 SPV315 | JIS G3115 SPV355 | JIS G3115 SPV410 |
| JIS G3115 SPV450 | JIS G3115 SPV490 | ||||
| JIS G3103 | JIS G3103 SB410 | JIS G3103 SB450 | JIS G3103 SB480 | JIS G3103 SB450M | |
| JIS G3103 SB480M | |||||
| GB | GB713 | GB713 Q245R | GB713 Q345R | GB713 Q370R | GB713 12Cr1MoVR |
| GB713 12Cr2Mo1R | GB713 13MnNiMoR | GB713 14Cr1MoR | GB713 15CrMoR | ||
| GB713 18MnMoNbR | |||||
| GB3531 | GB3531 09MnNiDR | GB3531 15MnNiDR | GB3531 16MnDR | ||
| DIN | DIN 17155 | DIN 17155 HI | DIN 17155 HII | DIN 17155 10CrMo910 | DIN 17155 13CrMo44 |
| DIN 17155 15Mo3 | DIN 17155 17Mn4 | DIN 17155 19Mn6 | |||




